Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 81:

  You attempt to perform an ESXi update on a Cisco UCS C250 server, but the update does not recognize the NICs. You must perform the update as quickly as possible. Which step must you do first?

  A. Check the UCS compatibility matrix and replace the NIC with a supported one.
  B. Reconfigure the NIC ID on the LOM.
  C. Update the LOM firmware by using the Cisco Host Update Utility.
  D. Update the NIC firmware by using the Cisco Host Update Utility.
  C. Update the LOM firmware by using the Cisco Host Update Utility.

• Question 82:

  What is the default number of dynamic vNICs that is specified by the Cisco UCS Manager when creating a dynamic vNIC connection policy?

  A. 54
  B. 128
  C. 256
  D. 257
  A. 54

• Question 83:

  You are attempting to install Microsoft Server 2008 R2 on a Fibre Channel LUN, but the installer does not see the LUN. You have used F6 to load the appropriate SCSI driver. What should your first troubleshooting step be?

  A. Email the SAN administrator to validate that your LUN is defined.
  B. Check the configuration of the vHBA in the service profile.
  C. Validate that the boot order is correct.
  D. Validate zoning on the Fibre Channel switch.
  E. Validate that the Fibre Channel uplink from the fabric interconnect is up.
  B. Check the configuration of the vHBA in the service profile.

• Question 84:

  Which two Cisco Nexus 2000-Series Fabric Extenders support connections to both Cisco Nexus 5000 Series Switches and Cisco Nexus 7000 Series Switches? (Choose two.)

  A. Cisco Nexus 2248TP
  B. Cisco Nexus 2248TP-E
  C. Cisco Nexus 2232PP
  D. Cisco Nexus 2232TM
  A. Cisco Nexus 2248TP
  C. Cisco Nexus 2232PP

• Question 85:

  Which option is a valid file extension for a CIMC configuration file?

  A. .xml
  B. .json
  C. .txt
  D. .exe
  E. .zip
  A. .xml

• Question 86:

  Which feature on the Cisco IMC GUI allows you to view the last boot post operation?

  A. Firmware Management tab
  B. Bootstrap Process Recording
  C. Crash Recording
  D. Trusted Platform Module
  B. Bootstrap Process Recording

• Question 87:

  Refer to the exhibit.

  

  Which link is down?

  A. Link1
  B. Link2
  C. Link3
  D. Link4
  C. Link3

• Question 88:

  Which statement is true about system event logs?

  A. By default, they require manual clearing.
  B. They report operating system crashes and errors.
  C. They are also referred to as system error logs.
  D. They can only be accessed from Cisco UCS Manager.
  A. By default, they require manual clearing.

• Question 89:

  A local storage installation of ESX on a Cisco UCS C-Series server has failed due to local storage issues. What is the cause of the problem?

  A. LSI drivers are not bundled with ESX.
  B. The hard drive has a 1-TB partition size.
  C. The server only has an onboard controller, while ESX requires an LSI RAID controller card.
  D. ESX is not supported on Cisco UCS C-series servers.
  C. The server only has an onboard controller, while ESX requires an LSI RAID controller card.

• Question 90:

  Which three statements are true about using the debug command to resolve an HSRP issue on the Cisco Nexus platform? (Choose three.)

  A. The debug command should be allowed to run for at least an hour.
  B. The administrator can log debug messages to a special log file to avoid flooding the console.
  C. Open a second Telnet or SSH session before you enter any debug commands so that if the debug session overwhelms the console, you can stop the message output.
  D. Use the debug command only under the guidance of Cisco Technical Support.
  E. Use the Ethanalyzer remote interface command to capture packets.
  F. The debug peer-gateway command should be used to isolate the problem.
  B. The administrator can log debug messages to a special log file to avoid flooding the console.
  C. Open a second Telnet or SSH session before you enter any debug commands so that if the debug session overwhelms the console, you can stop the message output.
  D. Use the debug command only under the guidance of Cisco Technical Support.