Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 91:

  HOTSPOT

  

  

  Hot Area:

  

  

• Question 92:

  What is the maximum number of boot targets for an FCoE vHBA on a Cisco UCS C-Series server?

  A. 1
  B. 2
  C. 3
  D. 4
  D. 4

• Question 93:

  Refer to the exhibit.

  

  VM-1 and VM-3 are in different EPG-3 are in different EPGs but in the same BD. Which statement about the communication between VM-1 and VM-3 is true?

  A. The flow uses encapsulated VLANs.
  B. The flow must transverse the spine.
  C. The packet must transverse a Layer 3 interface.
  D. The flow stays local to the leaf switch.
  B. The flow must transverse the spine.

• Question 94:

  

  

  What is the reason that no C-Series servers can access Fibre Channel storage from this Cisco Nexus 554SUP switch?

  A. Zoning mode mis-match with the MDS 9124
  B. There are no active Fibre Channel interfaces
  C. VSAN mis-match on Fibre Channel interfaces
  D. None of the virtual fibre channel interfaces are configured
  C. VSAN mis-match on Fibre Channel interfaces

• Question 95:

  Which two commands will show all the OTV edge devices and their MAC addresses in all sites in the overlay? (Choose two.)

  A. show otv adjacency overlay
  B. show otv site
  C. show otv vlan
  D. show otv adjacency
  E. show mac address-table
  A. show otv adjacency overlay
  D. show otv adjacency

• Question 96:

  Refer to the exhibit.

  

  You see the fault when configuring a global ID pool in Cisco UCS Central. Which scenario could cause the issue?

  A. The same ID is defined in Cisco UCS Central and Cisco UCS Manager.
  B. Global service profiles consume IDs from the blocks that have an assigned ID range qualifier.
  C. The same IP address is configured in two registered domains.
  D. The same ID is assigned to the service profiles in two registered domains.
  D. The same ID is assigned to the service profiles in two registered domains.

• Question 97:

  After a data center is upgraded with new Cisco Nexus switches, some of the links using multimode fiber no longer work, which type Of multimode cables are valid?

  A. OM4 cable for 700 mat 10 Gb
  B. OM3 cable for 50 m at 40 Gb with QSFP BiDi
  C. OM4 cable for 150 m at 40 Gb QSFP BiDi
  D. OM2 cable for 550 mat 10 Gb
  B. OM3 cable for 50 m at 40 Gb with QSFP BiDi

• Question 98:

  Which actions on a Cisco UCS Server can be performed under the Cisco IMC utilities? (Choose Four.)

  A. export tech support information to a remote host
  B. download a tech support file locally
  C. reboot the Cisco IMC
  D. recover a corrupt BIOS
  E. install firmware updates
  A. export tech support information to a remote host
  B. download a tech support file locally
  C. reboot the Cisco IMC
  D. recover a corrupt BIOS

• Question 99:

  Refer to the exhibit. Which two options are causes of the error when setting up VM-FEX on the Cisco UCS B-Series Blades? (Choose two.)

  

  A. Dynamic vNICs are not supported on the version the admin is running.
  B. The network adapter in the blade does not support dynamic vNICs.
  C. Too many dynamic vNICs are configured.
  D. Dynamic vNICs are not required for VM-FEX.
  E. The dynamic vNIC connection policy was never applied to the service profile.
  B. The network adapter in the blade does not support dynamic vNICs.
  C. Too many dynamic vNICs are configured.

• Question 100:

  A customer is deploying FCoE in its network and has found that the connected host does not support FIP. Which command will be useful in troubleshooting this issue?

  A. show platform fcoe_mgr info interface vfc id
  B. show platform fcoe_mgr info software interface vfc id
  C. show platform software fcoe_mgr info interface vfc id
  D. show platform software interface fcoe_mgr info vfc id
  C. show platform software fcoe_mgr info interface vfc id