Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 471:

  Which tool can be used to browse the Cisco APIC Management Information Tree via a web browser?

  A. Kafka
  B. Spark
  C. Maven
  D. \/isore
  D. \/isore

• Question 472:

  Which CLI command will indicate whether a Cisco UCS C-Series rack-mount server has any failed DIMMs?

  A. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-summary
  B. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-fault
  C. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-ecc
  D. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-recovery
  A. ucs-c250 / # scope chassis ucs-c250 /chassis # show dimm-summary

• Question 473:

  Refer to the exhibit.

  

  Which statement describes the output of the command?

  A. The VSM is connected to the vCenter server.
  B. The ports of the host are added to the DVS on VLAN 27.
  C. The DPA interface is configured to use the incorrect VLAN.
  D. The active VSM is connected to the standby VSM.
  B. The ports of the host are added to the DVS on VLAN 27.

• Question 474:

  DRAG DROP

  You are troubleshooting a SAN failure. Drag and drop the reason codes from the left into the types of affected ports on the right.

  Select and Place:

  

  

• Question 475:

  You are troubleshooting a Cisco UCS B-Series Blade Server. Drag and drop the issues from the left onto the reasons that can cause them on the right.

  Select and Place:

  

  

• Question 476:

  Which three statements explain why a Cisco UCS server cannot boot via SAN? (Choose three.)

  A. The correct VLAN must be configured.
  B. The correct WWPN must be specified in the service profile.
  C. The server must be able to ping the target.
  D. The correct boot order must be specified in the service profile.
  E. The boot LUN number must specify the appropriate operating system.
  B. The correct WWPN must be specified in the service profile.
  D. The correct boot order must be specified in the service profile.
  E. The boot LUN number must specify the appropriate operating system.

• Question 477:

  In a Cisco UCS environment, what are the three power types in a power policy? (Choose three.)

  A. backup
  B. grid
  C. redund
  D. n-plus-1
  E. non-redund
  F. plus-1
  B. grid
  D. n-plus-1
  E. non-redund

• Question 478:

  Refer to the exhibit.

  

  DC-SWITCH 14 is a Cisco Nexus switch Port channel 1106 connects to a Cisco Nexus switch named DC-SWITCH10. Which cause of the I flag is likely?

  A. Port channel 1106 is administratively down.
  B. STP is blocking port channel 1106
  C. LACP is misconfigured on DC-SWITCH14
  D. LACP is misconfigured on DC-SWITCH10.
  D. LACP is misconfigured on DC-SWITCH10.

• Question 479:

  UCS-A# scope eth-uplink UCS-A /eth-uplink # scope fabric a UCS-A /eth-uplink/fabric # scope interface 2 3 UCS-A /eth-uplink/fabric/interface # create mon-src Monitor23 UCS-A /eth-uplink/fabric/interface/mon-src* # set direction receive UCS-A /eth-uplink/fabric/interface/mon-src* # commit-buffer What does the command scope interface 2 3 in the above CLI command sequence do on a Cisco UCS blade server?

  A. enters the interface command mode for the specified uplink port
  B. enters the interface command mode for the specified Fabric A
  C. enters the interface command mode for the specified Fabric B
  D. enters slot 3 port 2 specified uplink port
  A. enters the interface command mode for the specified uplink port

• Question 480:

  Refer to the exhibit.

  

  When your customers have NPV problems, which two actions should you take? (Choose two.)

  A. Verify that the NPV core switch supports NPIV and that it is enabled.
  B. Ensure that the VLAN values are configured on both sides of the NPV core switch.
  C. Verify the status of the servers and external interfaces, using the show npv server status command.
  D. Ensure that the VSAN value that is configured on the device links is correct.
  E. For all the device links, ensure that the port mode on the NPV device is in Full_port mode.
  A. Verify that the NPV core switch supports NPIV and that it is enabled.
  D. Ensure that the VSAN value that is configured on the device links is correct.