Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 461:

  Which command can you use to determine if the member ports share the appropriate parameters in order to join a port channel?

  A. show port-channel summary
  B. show port-channel usage
  C. show port-channel compatibility-parameters
  D. show port-channel load-balance
  C. show port-channel compatibility-parameters

• Question 462:

  Refer to the exhibit.

  

  You fail to configure a boot from iSCSI service profile. Which action do you take to troubleshoot the issue?

  A. Attempt to ping the IP address of the iSCSI target.
  B. Check the LUN masking configuration.
  C. In the CLI of Cisco UCS Manager, verify that the blade is attached to the LUN.
  D. Check the native VLAN configuration on the overlay vNIC.
  D. Check the native VLAN configuration on the overlay vNIC.

• Question 463:

  Which three statements are true about the show cfs merge status name command? (Choose three.)

  A. In a successful merge, all switches in the fabric are shown separately.
  B. The command shows the complete Cisco Fabric Services region database.
  C. The command shows the merge status in all valid VSANs on the switch.
  D. The merge master is selected based on the highest sWWN in the fabric.
  E. The merge master is selected based on the lowest sWWN in the fabric.
  F. In a successful merge, all switches are shown in a local fabric.
  C. The command shows the merge status in all valid VSANs on the switch.
  E. The merge master is selected based on the lowest sWWN in the fabric.
  F. In a successful merge, all switches are shown in a local fabric.

• Question 464:

  There is an ARP storm in VDC 1. Some users on VDC 2 notice that ARP is not resolving for their gateway on the Cisco Nexus core. What is the cause?

  A. The ARP CoPP class committed information rate is exceeded, resulting in ARP loss in all VDCs.
  B. The administrator has not correctly configured the ARP CoPP class in VDC 2.
  C. The ARP traffic in VDC 1 is copied to the host ports in VDC 2, causing overutilization and output discards.
  D. Because the ARP process in the default VDC (VDC 1) is responsible for processing ARP traffic for all VDCs, VDC 2 will be affected.
  A. The ARP CoPP class committed information rate is exceeded, resulting in ARP loss in all VDCs.

• Question 465:

  When you look at the HSRP state for devices on a VLAN that is extended by OTV, you see the following states: Active, Standby, and Listen. However, you intended each data center device to show the state as Active and Standby. What is the problem?

  A. HSRP is not configured correctly.
  B. A VACL is missing.
  C. A PACL is missing.
  D. This cannot be done.
  B. A VACL is missing.

• Question 466:

  HOTSPOT

  

  

  

  Hot Area:

  

  

• Question 467:

  Which two of these would cause two switch fabrics not to merge? (Choose three.)

  A. The switches do not have at least one assigned domain ID in common.
  B. Two switches have different assigned VSANs on the connecting ports.
  C. The switches have different assigned VLANs on the connecting ports.
  D. The static domain ID does not override the dynamic ID.
  E. The election of the static domain is only determined by the WWNs of the two switches.
  B. Two switches have different assigned VSANs on the connecting ports.
  C. The switches have different assigned VLANs on the connecting ports.

• Question 468:

  Which two commands will show all the MAC addresses learned from remote sites in an OTV overlay? (Choose two.)

  A. show otv route overlay
  B. show otv vlan
  C. show ip arp
  D. show mac address-table
  E. show otv site
  A. show otv route overlay
  D. show mac address-table

• Question 469:

  HOTSPOT

  

  

  

  Hot Area:

  

  

• Question 470:

  Which private VLAN port type allows for the least amount of communication from that port to others?

  A. protected
  B. isolated
  C. community
  D. promiscuous
  B. isolated