Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 451:

  In end-host mode, for which type of port are MAC addresses stored in a forwarding table?

  A. monitoring
  B. cluster
  C. uplink
  D. server
  D. server

• Question 452:

  Refer to the exhibit.

  

  What is the cause of the ISSU failure when using the command show system internal csm global info?

  A. The command conf-t is holding a lock and not released it.
  B. The SSN feature is not enabled on both switches.
  C. The reference count is less than 1 due to a lack of successful config-sync.
  D. It cannot be determined from the output.
  E. An Administrator is logged in on another session and has a lock of the session data base to prevent ISSU.
  A. The command conf-t is holding a lock and not released it.

• Question 453:

  What the default MTU size of a VMware host?

  A. 1000
  B. 1500
  C. 1550
  D. 9000
  B. 1500

• Question 454:

  Refer to the exhibit.

  

  SAN-SW-1has failed and must be replaced. Your client reports that all servers are booting from storage array 2 even through storage array 1 is up and reachable by Cisco UCS infrastructure. Which reason is the root cause of the boot anomaly?

  A. SAN target primary under SAN primary must be changed to SAN target secondary under SAN secondary.
  B. San target primary under San secondary must be changed to SAN target secondary under SAN secondary.
  C. SAN target primary under SAN secondary must be changed to SAN target secondary under SAN primary.
  D. SAN target secondary must be added to primary and SAN secondary.
  D. SAN target secondary must be added to primary and SAN secondary.

• Question 455:

  HOTSPOT

  

  

  Hot Area:

  

  

• Question 456:

  HOTSPOT

  

  

  

  Hot Area:

  

  

• Question 457:

  If no traffic was ever sent across the overlay, what will the show mac address-table command on the OTV VDC indicate?

  A. invalid command
  B. the MAC address of the local OTV join interface
  C. the system IDs of all the local OTV edge devices
  D. the system IDs of all the local and remote edge devices in the overlay
  E. all the MAC addresses learned on the extended VLAN
  B. the MAC address of the local OTV join interface

• Question 458:

  Refer to the exhibit.

  

  Which action removes the system designation from VLAN 70?

  A. Create another port profile that excludes VLAN 70.
  B. Shut down the port profile first.
  C. Delete the uplink-storage port profile, and then receive it.
  D. Remove VLAN 70 from the trunk first.
  C. Delete the uplink-storage port profile, and then receive it.

• Question 459:

  You successfully install VMware ESXi 5.0 U1 on a Cisco UCS B200 M3 server to a Fibre Channel LUN. When you reboot the server, you see the message "Reboot and Select Proper Boot device or insert Boot Media in selected Boot device and press a key." What are the first two pieces of information you should gather to troubleshoot the boot failure? (Choose two.)

  A. Connect to the NX-OS shell via the CLI and run the show npv flogi-table command.
  B. SSH to the MDS 9124 and run the show flogi database command.
  C. Validate the boot target WWPN and LUN ID in the service profile.
  D. Validate the correct source WWPN in the service profile vHBA definition.
  E. Validate zoning for your WWPN on the Cisco MDS 9124.
  F. Validate that the boot order indicates the vHBA as the first device.
  G. Ensure LUN masking is correctly configured on the storage controller.
  C. Validate the boot target WWPN and LUN ID in the service profile.
  F. Validate that the boot order indicates the vHBA as the first device.

• Question 460:

  Which statement is true about the show cfs merge status name command?

  A. In a successful merge, all switches in the fabric are shown separately.
  B. The command shows the complete Cisco Fabric Services region database.
  C. The merge master is selected based on the highest sWWN in the fabric.
  D. In a successful merge, all switches are shown in a local fabric.
  D. In a successful merge, all switches are shown in a local fabric.