Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 321:

  Which action do you take to determine why the interface e1/10 is not present in the core VDC for configuration?

  A. Check the admin VDC to see the port e1/10 is allocated.
  B. Check the core VDC to see if the port e1/10 is allocated.
  C. Check to see if the cable is connected to the e1/10 interface,
  D. Check to see if vPC is enabled
  B. Check the core VDC to see if the port e1/10 is allocated.

• Question 322:

  Refer to the exhibit.

  

  Which action resolves the problem?

  A. Disable NPIV on the switch.
  B. Enable F Port mode on the link to the NPV switch.
  C. Configure the correct FC ID on the switch.
  D. Change the VSAN in which the port is located.
  B. Enable F Port mode on the link to the NPV switch.

• Question 323:

  Which Cisco UCS C Series command sequence initiates the sending of a technical support file to a TFTP server?

  A. ucs /cimc # scope tech-support ucs /cimc/tech-support # set ip 10.1.1.1 ucs /cimc/tech- support *# set tftp-path \showtechsupport ucs /cimc/tech-support *#commit ucs /cimc/tech- support *#start
  B. ucs /cimc # scope tech-support ucs /cimc/tech-support # set tftp-ip 10.1.1.1 ucs /cimc/tech-support *# set path \showtechsupport ucs /cimc/tech-support *#commit ucs /cimc/tech-support *#start
  C. ucs /cimc # scope support ucs /cimc/support # set tftp-ip 10.1.1.1 ucs /cimc/support *# set path \showtechsupport ucs /cimc/support *#commit ucs /cimc/support *#start
  D. ucs /cimc # scope system-support ucs /cimc/system-support # set tftp-ip 10.1.1.1 ucs /cimc/system-support *# set path \showtechsupport ucs /cimc/system-support *#commit ucs /cimc/system-support *#start
  B. ucs /cimc # scope tech-support ucs /cimc/tech-support # set tftp-ip 10.1.1.1 ucs /cimc/tech-support *# set path \showtechsupport ucs /cimc/tech-support *#commit ucs /cimc/tech-support *#start

• Question 324:

  Refer to the exhibit.

  

  Anycast RP fails. Which two actions do you perform to resolve the issue? (Choose two.)

  A. Configure the IP address of Anycast RP to use the multicast range.
  B. Change the loopback2 interface on Nexus 2 to 10.1.1.1/32.
  C. Change the pim rp-address on Nexus 2 to 10.1.1.1.
  D. Add the pim ssm range to Nexus 1.
  E. Set the pim ssm range on Nexus 2 to 225.0.0.0/24
  B. Change the loopback2 interface on Nexus 2 to 10.1.1.1/32.
  C. Change the pim rp-address on Nexus 2 to 10.1.1.1.

• Question 325:

  Refer to the exhibit.

  

  The output displays a failed SFP validation. What is the cause of the failure?

  A. The fiber is not connected to the SFP
  B. The SFP is not a valid Cisco SFP
  C. The speed needs to be changed to 10000,
  D. The speed needs to be changed to 1000
  A. The fiber is not connected to the SFP

• Question 326:

  You have a vPC that is in a blocking state. Which issue can cause this problem?

  A. You have a MAC address filter applied.
  B. You have Bridge Assurance enabled on the vPC.
  C. VLANs are missing from the peer link.
  D. You have a Type 1 Configuration Element Mismatch
  B. You have Bridge Assurance enabled on the vPC.

• Question 327:

  You receive a priority 1 trouble ticket that there is OSPF route instability in the data center core Cisco Nexus 7018 Switches. Which command is useful to help validate a theory that hello packets are being throttled?

  A. N7018# show class-map interface control-plane
  B. N7018# show policy-map interface control-plane
  C. N7018# show service-policy interface control-plane
  D. N7018# show copp status
  E. N7018# show copp statistics
  F. N7018# show control-plane class copp-system-class-critical
  B. N7018# show policy-map interface control-plane

• Question 328:

  In new Cisco UCS release 2.0 installations, what are the default VLAN IDs?

  A. Ethernet VLAN default ID is 4048, FCOE default VLAN ID 4048
  B. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 3968
  C. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 2
  D. Ethernet VLAN default ID is 2, FCOE default VLAN ID is 4047
  E. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 4048
  E. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 4048

• Question 329:

  You are troubleshooting an FCoE boot issue on a Cisco UCS C220 M3 server with a VIC 1225 CNA. Which two pieces of information can you directly infer from the output of the show zone active command below? (Choose two.)

  zone name Server_1-to-Storage vsan 11 pwwn 50:06:01:60:3b:a0:08:9f [Storage]

  *

  fcid 0x3b000b [pwwn 20:00:00:25:b5:04:0a:02] [C22_Server]

  A. The storage controller is not logged into the fabric.
  B. The server is not logged into the fabric.
  C. Only the storage controller is logged into the fabric.
  D. Only the server is logged into the fabric.
  E. The initiator and target cannot communicate because they are on the wrong VSAN.
  F. The WWPN of the storage controller is mistyped.
  G. The initiator and target cannot communicate because the zone name does not match the server name (C22_Server).
  A. The storage controller is not logged into the fabric.
  D. Only the server is logged into the fabric.

• Question 330:

  Which command is critical in order for OTV edge devices to maintain an overlay adjacency with their local peers in a multihomed site via the join interfaces across the Layer 3 network domain?

  A. otv site-identifier
  B. otv extend-vlan
  C. otv site-vlan
  D. otv use-adjacency-server unicast-only
  A. otv site-identifier