Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 311:

  Which two statements are true regarding vPC?

  A. There is higher oversubscription
  B. STP is disabled.
  C. With vPC, there are no blocked ports
  D. There is VLAN-based load balancing.
  E. A peer link is required.
  B. STP is disabled.
  C. With vPC, there are no blocked ports

• Question 312:

  You use a Cisco UCS VIC 1340 adapter. You discover that the actual vNIC order does not reflect the order specified in the connectivity policy. What must you do to change the placement order?

  A. Change adminHostPort in the vNIC policy.
  B. Change the adapter order in the connectivity policy.
  C. Remove all of the adapters and recreate all of the adapters in the required order
  D. Change adminHostPort in the connectivity policy.
  A. Change adminHostPort in the vNIC policy.

• Question 313:

  A switch is configured with the following command:

  switch(config)# aaa authentication login default group tacacs+

  What occurs when an AAA login authentication request fails to communicate with any of the servers in the group?

  A. The authentication request fails.
  B. The local database is used for authentication.
  C. The authentication request is successful.
  D. A server in another server group is used, if present.
  A. The authentication request fails.

• Question 314:

  Refer to the exhibit.

  

  Interfaces Ethernet 7/1-8 are members of the CORE-SW1 VDC, and CORE-7700-1 is the admin VDC. Which cause of the error is likely?

  A. The FCoE VLANs associated to Ethernet 7/1-8 must be assigned to the FC-CORE-SW1 VDC in the admin VDCs.
  B. Interfaces Ethernet 7/1-8 must be configured for FCoE sharing.
  C. All the interfaces in the FC-CORE-SW1 VDC must be configured for FCoE sharing.
  D. The Fibre Channel VSANs associated to Ethernet 7/1-8 must be assigned to the FC- CORE-SW1 VDC in the admin VDCs.
  A. The FCoE VLANs associated to Ethernet 7/1-8 must be assigned to the FC-CORE-SW1 VDC in the admin VDCs.

• Question 315:

  When troubleshooting a VXLAN on a Cisco Nexus 9000 Series Switch, which information can you verify by running the show nve vni command?

  A. the VxLAN VNI status
  B. the VXLAN to VLAN mapping
  C. the MAC Address table
  D. the Overlay Peer
  A. the VxLAN VNI status

• Question 316:

  Some of your servers do not have IP connectivity to the upstream network. Which two commands do you use to identify whether a data path is up and running on a switch? (Choose two.)

  A. show platform fwm info hw-stm
  B. show interface brief
  C. show npvflogi-table
  D. show mac-address table
  E. show pinning border-interfaces active
  B. show interface brief
  D. show mac-address table

• Question 317:

  Refer to the exhibit.

  

  You install a new Cisco Nexus F3-Series module on a Nexus 7700 Series switch. When you attempt to allocate an interface from the module to a new VDC, an error occurs. Which issus could the error?

  A. Cisco o Nexus F3-Series modules are unsupported in VDCs.
  B. The limit-resource vlan minimum 16 maximum 4094 command missing.
  C. The limit-resource module-type f3 command is missing.
  D. Cisco Nexus f3-Series modules are unsupported on Nexus 7700 Series Switches.
  C. The limit-resource module-type f3 command is missing.

• Question 318:

  Refer to the exhibit.

  

  The VXLAN configuration fails. Which action do you take to resolve the issue?

  A. Change the multicast address in the 232.0.0.0/8 range.
  B. Change the mask of loopback1 to 255.255.255.255.
  C. Use a transit interface as the source interface.
  D. Enable dense mode on loopback1.
  B. Change the mask of loopback1 to 255.255.255.255.

• Question 319:

  Before using the UCS Manager to configure SAN and network connectivity in the service profile, which two components needs to be created? (Choose two.)

  A. vHBA
  B. global VSAN
  C. vNIC
  D. global VLAN
  B. global VSAN
  D. global VLAN

• Question 320:

  HOTSPOT

  

  

  

  Hot Area: