Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 331:

  You are troubleshooting Cisco AVS by using the CLI of the VMware ESXi host. You must get this information. Dvs name, Remote IP, Port, and Switching Mode. Which command do you run?

  A. vemcmd show port
  B. vem status
  C. vemcmd show openflex
  D. vemcmd show sod
  B. vem status

• Question 332:

  A customer starts an Auto Install upgrade process. During the process, the customer selects the wrong firmware version. Which action rolls back to the previous firmware version as quickly as possible?

  A. Cancel the process by using the Cisco UCS Manager.
  B. Wait for the upgrade to complete, and then roll back the configuration.
  C. Wait for the upgrade to complete, and then downgrade.
  D. Cancel the process by using the CLI.
  C. Wait for the upgrade to complete, and then downgrade.

• Question 333:

  Refer to the exhibit.

  

  A customer is having a problem getting NPV to work. What is causing the problem?

  A. The core NPV switch port is not an F port.
  B. The core NPV switch port is in a shutdown state.
  C. The core NPV switch port is not configured on both ends.
  D. The core NPV switch port is not configured on the other end.
  E. The core NPV switch ports are in the wrong domain.
  A. The core NPV switch port is not an F port.

• Question 334:

  What is the first step Cisco recommends for recovering a fabric interconnect when you have no working images on the bootflash?

  A. Reboot the primary fabric interconnect.
  B. Receive the kickstart image by using TFTP.
  C. Reboot the secondary fabric interconnect.
  D. Initiate auto-install.
  B. Receive the kickstart image by using TFTP.

• Question 335:

  You are attempting to configure boot from SAN on your server that is attached to a Cisco MDS 9148 Fibre Channel switch. What is a possible issue that may occur?

  A. Check the status of the licenses on the Fibre Channel switch.
  B. NPV is not configured on the Fibre Channel switch.
  C. NPIV is not configured on the Fibre Channel switch.
  D. Boot from SAN is not supported via the Fibre Channel protocol.
  C. NPIV is not configured on the Fibre Channel switch.

• Question 336:

  Refer to the exhibit.

  

  In a Cisco UCS environment, which switch mode does the exhibit portray?

  A. end host mode
  B. switching mode
  C. access mode
  D. core mode
  A. end host mode

• Question 337:

  When a service profile is disassociated from a server, what happens to the identity and connectivity information for the server?

  A. It is cleared and set to the default that was setup initially by the first configuration.
  B. It is maintained and can be reused.
  C. It is reset to factory defaults.
  D. It uses master service profile parameters.
  E. It takes parameters of other servers in the service profile.
  B. It is maintained and can be reused.

• Question 338:

  You have a node in a decommissioned state. What could cause the issue?

  A. The node cannot join the fabric.
  B. The node is in a transient state.
  C. The node was disabled by the user.
  D. The node is unreachable.
  C. The node was disabled by the user.

• Question 339:

  Which two occurrences happen during an ISSU? (Choose two.)

  A. FLOGI/fdisc or logo requests from servers fail until the ISSU is complete.
  B. The time-to-live value for CDP is increased (360 seconds) if it is less than the recommended timeout value.
  C. LACP is not affected because ISSU should not impact peers that rely on LACP because the recovery time is less than 90 seconds.
  D. NTP sessions stay alive and active.
  E. The control plane is offline for up to 300 seconds.
  A. FLOGI/fdisc or logo requests from servers fail until the ISSU is complete.
  C. LACP is not affected because ISSU should not impact peers that rely on LACP because the recovery time is less than 90 seconds.

• Question 340:

  

  Refer to the exhibit. You are attempting to trace packet flow from server1/1 to the fabric. On which interface does traffic leave from server 1/1?

  A. fabric A
  B. Po10
  C. fabric B
  D. Po30
  A. fabric A