Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 301:

  

  

  It has been determined that unknown unicast, multicast, and broadcast traffic is not correctly being switched through either Nexus 7010 switch. Which statement best describes the cause of this issue?

  A. No VLANs are allowed across the vPC peer link.
  B. The MST STP is not enabled on either switch.
  C. The default VLAN is inactive.
  D. VTP is not configured to handle this type of traffic.
  B. The MST STP is not enabled on either switch.

• Question 302:

  A customer has a Cisco UCS Center cluster. The customer configures LDAP as the AAA protocol and enables SSL for LDAP. The LDAP authentication fails. Which issue is the cause of the failure?

  A. The LDAP client passed an incorrect from the trustpoint.
  B. The ca certificate is missing from the trustpoints.
  C. The LDAP server limit that is set by an administrative authority was exceeded.
  D. The LDAP time limit that is specified by either the client or the server was exceeded.
  B. The ca certificate is missing from the trustpoints.

• Question 303:

  Refer to the exhibit.

  

  You connect Cisco Nexus 5600 Series switches to Cisco Nexus 2200 Series Fabric Extenders by using FET-10G SFPs. Which command resolves the error that is shown in the exhibit?

  A. switch#(config-if)# switchport mode dotlq tunnel trunk
  B. switch#(config-if)# switchport mode fex-fabric
  C. switch#(config-if)# switchport mode dynamic desirable
  D. switch#(config-if)# switchport mode fabricpath
  B. switch#(config-if)# switchport mode fex-fabric

• Question 304:

  OTV is configured ?test pings confirm that it is working but other tests do not seem to perform well. What is the problem?

  A. VLANs are not properly extended.
  B. The multicast groups are not defined properly.
  C. The transport network is not configured to process the overhead that is introduced by OTV.
  D. The overlay may not be enabled.
  C. The transport network is not configured to process the overhead that is introduced by OTV.

• Question 305:

  Which two commands will show all the OTV edge devices and their MAC addresses in the local site? (Choose two.)

  A. show otv overlay
  B. show otv site
  C. show otv vlan
  D. show otv adjacency
  E. show mac address-table
  B. show otv site
  D. show otv adjacency

• Question 306:

  Which option describes how you can reset the BIOS password of a Cisco UCS C-Series Rack-Mount Server?

  A. Turn off the server. Press and hold the F7 key, and then turn on the server.
  B. Reset the jumper on the motherboard.
  C. Press and hold the power switch for 20 seconds.
  D. Turn off the server. Press and hold the F2 key, and then turn on the server.
  B. Reset the jumper on the motherboard.

• Question 307:

  In Cisco UCS, which logs are used to troubleshoot hardware failure?

  A. system event log
  B. audit log
  C. gateway logs
  D. system log
  A. system event log

• Question 308:

  What task is required before adding traffic sources to a monitoring session?

  A. create a traffic monitoring session
  B. choose a source component
  C. activate the session
  D. delete any earlier data collection
  A. create a traffic monitoring session

• Question 309:

  Which option is a best practice that should be followed When replacing a CISCO Nexus 5000 Series switch in a vPC topology?

  A. Connect a dual-homed Fabric Extender topology fabric port to the replacement switch.
  B. Ensure that the vPC role priority of the replacement switch is equal to the existing swtch.
  C. Obtain the configuration from the peer switch if the configuration synchronization feature was enabled.
  D. Ensure that the vPC role priorty of the replacement switch is better than the existing switch
  C. Obtain the configuration from the peer switch if the configuration synchronization feature was enabled.

• Question 310:

  Looking at the Equipment > Chassis > Servers > Server X view from the Cisco UCS Manager GUI, which tab would you select to identify the fabric interconnect uplink associated with a given virtual circuit?

  A. Paths
  B. vNIC Paths
  C. Virtual Circuit Paths
  D. VIF Paths
  D. VIF Paths