Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 291:

  Which command must you use to find information about system event logs?

  A. UCS-TEST-DMZ-A/security #show audit-logs
  B. UCS-TEST-DMZ-A/cimc/log#show entries
  C. UCS-TEST-DMZ-A/system/control-ep#show communication-policy-ctrl
  D. UCS-TEST-DMZ-A#/org/service-profile#show pending-changes detail
  B. UCS-TEST-DMZ-A/cimc/log#show entries

• Question 292:

  When you ping your new Cisco Nexus 7010 Switch, you see this output:

  !!...!!...!!...!!...!!...

  What could be the problem?

  A. Traffic may be taking a bad route through the network.
  B. HSRP is flapping.
  C. CoPP is rate-limiting the pings.
  D. The switch has high CPU utilization.
  C. CoPP is rate-limiting the pings.

• Question 293:

  Refer to the exhibit.

  

  Which conditions can trigger on a Cisco Nexus device running FabricPath?

  A. A switch connected to the Cisco Nexus device is running RSTP instead of STP.
  B. A BPDU with bridge priority set to 61140 is received by the switch edge port.
  C. The switch edge port in the STP domain is not configured as root.
  D. VLAN is configured incorrectly on port-channel 100.
  C. The switch edge port in the STP domain is not configured as root.

• Question 294:

  A Cisco Nexus 7010 Switch that is at the core of a customer network has high CPU utilization. What can the customer do to prevent a network outage and identify why CPU utilization is high?

  A. apply a rate limit on the interfaces with high traffic
  B. use CoPP
  C. use HSRP and vPC for redundancy to handle high CPU utilization
  D. use the show process cpu command to see the high CPU utilization
  B. use CoPP

• Question 295:

  Refer to the exhibit.

  

  You configure a vPC between two Cisco Nexus 7010 Switches. The peer link will not come up. What is the problem?

  A. The vPC domain numbers must be different.
  B. The role priority must be the same.
  C. The system priority must be the same.
  D. The configuration is incorrect.
  C. The system priority must be the same.

• Question 296:

  Refer to the exhibit.

  You are troubleshooting a Cisco FabricPath anycast HSRP configuration issue. What is the cause of the issue?

  

  A. HSRP version 2 must be used with HSRP anycast.
  B. The switch ID that is used in each switch configuration must be different.
  C. L1 and L2 would not be connected.
  D. The priority for S1 and S2 is the same in each switch configuration.
  B. The switch ID that is used in each switch configuration must be different.

• Question 297:

  Refer to the exhibit.

  

  CORE-01 fails, which causes a three-second outage. You must improve spanning tree convergence. Which action do you take?

  A. Configure the STP root manually
  B. Configure the peer-switch command under the vPC domain
  C. Ensure that the RSTP root is also the vPC primary peer
  D. Configure MST instead of RSTP.
  B. Configure the peer-switch command under the vPC domain

• Question 298:

  When you configure the settings for the core file exporter via UCS Manager, which field is required to configure a destination for the core files?

  A. Admin State
  B. Description
  C. Port
  D. Hostname
  E. Path
  D. Hostname

• Question 299:

  Which description of a core file is true?

  A. It is generated by a system failure.
  B. It is generated by a process failure.
  C. It is generated by a component failure.
  D. It is generated by a hardware failure.
  B. It is generated by a process failure.

• Question 300:

  Which names are reserved when custom roles are created in Cisco UCS Manager RBAC?

  A. network-admin, network-operator, vdc-admin, vdc-operator, and server-admin
  B. cisco, cisco123, cisco-operator, cisco-admin, and root
  C. ucs-admin, ucs-operator, server-admin, server-operator, and cisco-admin
  D. ucs, ucs123, server-admin, server-operator, and sysroot
  A. network-admin, network-operator, vdc-admin, vdc-operator, and server-admin