Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 191:

  The Core File Exporter automatically exports cores to a remote server as they are generated. Which protocol does it use for this action?

  A. FTP
  B. SCP
  C. SFTP
  D. TFTP
  D. TFTP

• Question 192:

  

  What is the FCF-MAC tor this switch?

  A. 54:7f:ee:98:9b:39
  B. 54:7f:ee:98:9b:40
  C. 54:7f:ee:98:9b:41
  D. 54:7f:ee:98:9b:42
  E. 54:7f:ee:98:9b:43
  E. 54:7f:ee:98:9b:43

• Question 193:

  Refer to the exhibit.

  

  You have a server that fails to boot *which option is a possible cause of the issue?

  A. an incorrect boot policy
  B. incorrect zoning
  C. an incorrect FC/FCoE target port in the SAN
  D. incorrect LUN masking on the Storage array
  D. incorrect LUN masking on the Storage array

• Question 194:

  On a Cisco Nexus 5000 switch that runs in NPV mode, what is the correct command to view logged-in devices?

  A. show flogi database
  B. show npv flogi-table
  C. show npv status
  D. show npv device-login
  E. show fcns flogi-database
  B. show npv flogi-table

• Question 195:

  After you hot swap an HDD, the updated HDD metrics fail to appear in the Cisco UCS Manager GUI. Which option is the most likely cause of the problem?

  A. The Cisco UCS Manager gathers hard disk metrics only during a system boot.
  B. The hard disk firmware version is unsupported.
  C. The hard disk failed to initialize.
  D. The hard disk is a member of a RAID-1 array.
  A. The Cisco UCS Manager gathers hard disk metrics only during a system boot.

• Question 196:

  You have a Cisco APIC that has a VIC 1225 adapter installed, Fabric discovery fails. You verify that the cabling is correct, but the LLDP fails, Which option is a possible cause of the failed fabric discovery?

  A. incorrect VIC adapter firmware version
  B. Incorrect Cisco Nexus firmware version
  C. an SFP transceiver issue
  D. less than three APICs
  A. incorrect VIC adapter firmware version

• Question 197:

  Which CLI command identifies the service profile that is associated with a particular compute blade, VIF, vNIC type, link state, and pinned interface?

  A. show service-profile path server 1/2
  B. show service-profile circuit server 1/2
  C. show server-blade circuit server 1/2
  D. show server-blade path server 1/2
  B. show service-profile circuit server 1/2

• Question 198:

  Which two commands or tools must you use to recover from a zone merge failure in VSAN 10? (Choose two.)

  A. switch# zoneset import interface fc 1/3 vsan 10
  B. Fabric Manager > Zone > Merge Analysis
  C. switch(config)# import zoneset interface fc 1/3 vsan 10
  D. Fabric Manager > Zone > Merge Fail Recovery
  E. switch# import zoneset interface fc 1/3 vsan 10
  F. switch(config)# zoneset import interface fc 1/3 vsan 10
  A. switch# zoneset import interface fc 1/3 vsan 10
  B. Fabric Manager > Zone > Merge Analysis

• Question 199:

  You must check the path that vNICs uses to communicate. How can you verify whether a vNIC on a Cisco UCS server is in an active state or a failover state?

  A. Run the show interface brief command.
  B. Connect to the adapter and execute the Master Control Program.
  C. Compare the state on both fabric interconnects.
  D. Run the show interface status command.
  C. Compare the state on both fabric interconnects.

• Question 200:

  Refer to the exhibit.

  

  The server port connected to the NPV edge switch does not come online. Which action should fix the problem?

  A. Move the NP ports on the NPV edge and the F ports on the NPIV into the same VSAN 99.
  B. Move the NP ports on the NPV edge and the F ports on the NPIV in the default VSAN 1.
  C. Move all the ports into VLAN 1.
  D. Move all the ports into VSAN 99.
  E. Move all the ports into VLAN 99.
  A. Move the NP ports on the NPV edge and the F ports on the NPIV into the same VSAN 99.