Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 201:

  Refer to the exhibit. A server has a service profile that is configured to boot over iSCSI. During boot, this message is displayed. What is the cause of this message?

  

  A. The local disk is not present.
  B. RAID 0 is not configured on the local disk.
  C. The remote disk is powered off.
  D. The server has not configured the pWWN properly in the boot policy.
  C. The remote disk is powered off.

• Question 202:

  You have a Cisco UCS cluster and you must recover a lost admin password. In which order must you power cycle the fabric interconnects?

  A. primary first, and then secondary
  B. secondary first, and then primary
  C. primary and secondary simultaneously
  D. primary only
  B. secondary first, and then primary

• Question 203:

  Refer to the exhibit.

  

  You have two Cisco Nexus 9000 Series Switches named SwitchA and SwitchB. SwitchA resides in Area 49.0001. SwitchB resides in Area 49.0002 and connects to the Ethernet 2/1 interface on SwitchA. The configuration of SwitchA is shown in the exhibit. SwitchA cannot see IS-IS routing updates from SwitchB.

  What is a possible cause of the issue?

  A. The is-type configuration in router configuration mode and the isis circuit type configuration on the interface are misconfigured on SwitchA.
  B. The IS-IS NSAP address is missing on the Ethernet 2/1 interface of SwitchA.
  C. The neighbor statement defining SwitchB is missing on the Ethernet 2/1 interface of SwitchA.
  D. Area 49 0002 is not configured on SwitchA.
  A. The is-type configuration in router configuration mode and the isis circuit type configuration on the interface are misconfigured on SwitchA.

• Question 204:

  Which two statements are true about the OTV otv site-identifier id command? (Choose two.)

  A. It is used to determine if there are other OTV edge devices on the local site.
  B. It is used to identify the site to other OTV sites in the network.
  C. It should be configured in addition to the otv site-vlan command.
  D. It should be configured instead of the otv site-vlan command.
  E. The value should be the same across all OTV sites.
  A. It is used to determine if there are other OTV edge devices on the local site.
  C. It should be configured in addition to the otv site-vlan command.

• Question 205:

  Which tools can assist in the troubleshooting of FC-0 issues? (Choose three.)

  A. FC analyzer
  B. SPAN
  C. Device Manager
  D. show interface fc1/1 optical-power-budget
  E. PAA
  F. a portable protocol analyzer
  A. FC analyzer
  C. Device Manager
  F. a portable protocol analyzer

• Question 206:

  You have a Cisco UCS Central cluster. An I/O error is detected in the shared storage. What is a possible cause of the issue?

  A. One of the Cisco UCS Central nodes is powered off.
  B. The wrong path selection policy is configured in VMware.
  C. The shared storage LUN was shared by a virtual machine other than the Cisco UCS Central cluster nodes.
  D. The Cisco UCS domain is not registered in Cisco UCS Central.
  C. The shared storage LUN was shared by a virtual machine other than the Cisco UCS Central cluster nodes.

• Question 207:

  An engineer enters the show svs neighbors command as shown below. Which statement describes the output of the command?

  

  A. The VSM cannot connect to the VEM.
  B. The vCenter server cannot connect to the VSM.
  C. The VSM is connected to the VEM by using an Layer 2 network.
  D. The VSM is connected to the VEM by using an Layer 3 network.
  B. The vCenter server cannot connect to the VSM.

• Question 208:

  Which two statements about configuring NPV are true? (Choose two.)

  A. Only F, E, and SD ports are supported in NPV mode.
  B. Only targets can be connected to an NPV device.
  C. Distribute the NPV core switch links to different port groups for improved scalability.
  D. If DPVM is configured on the NPV core switch for an end device that is connected to the NPV device, then that end device must be configured to be in the same VSAN.
  E. NPV does not support NPIV-capable module servers (nested NPIV).
  C. Distribute the NPV core switch links to different port groups for improved scalability.
  D. If DPVM is configured on the NPV core switch for an end device that is connected to the NPV device, then that end device must be configured to be in the same VSAN.

• Question 209:

  A customer is configuring a network control policy in a Cisco UCS domain. The network control policy configures the network control settings for the Cisco UCS domain, including which three of these? (Choose three.)

  A. how the VIF behaves if no uplink port is available in end-host mode
  B. the action that the Cisco UCS Manager takes on the remote Ethernet interface, vEthernet interface, or vFibreChannel interface when the associated border port fails
  C. Layer 2 switching on the fabric interconnect
  D. whether MAC registration occurs on a per-vNIC basis or for all VLANs
  E. the end-host mode setting on the I/O module
  A. how the VIF behaves if no uplink port is available in end-host mode
  B. the action that the Cisco UCS Manager takes on the remote Ethernet interface, vEthernet interface, or vFibreChannel interface when the associated border port fails
  D. whether MAC registration occurs on a per-vNIC basis or for all VLANs

• Question 210:

  Two fabric interconnects fail during a Cisco UCS firmware upgrade. Drag and drop the recovery steps from the left into the correct order on the right.

  Select and Place: