HP HPE6-A41 Online Practice Questions and Exam Preparation

HP HPE6-A41 Online Questions & Answers

• Question 1:

  Refer to the exhibit.

  

  Which feature should the network administrator configure on the Virtual Switching Framework (VSF) fabric to prevent issues if Links 1 and 2 fail?

  A. Graceful OSPF (non-stop forwarding)
  B. Multi-Active Detection (MAD)
  C. Distributed trunking
  D. Virtual Router Redundancy Protocol (VRRP)
  B. Multi-Active Detection (MAD)

• Question 2:

  A company has these requirements to manage its ArubaOS switches:

  Management and data traffic cannot share links.

  Managers must be able to reach switches remotely over IP connections.

  How should the administrator set up switches to meet these requirements?

  A. Assign at least one port on each switch to a Virtual Switching Framework (VSF) link and connect those ports in a dedicated network.
  B. Create a management VLAN and tag the VLAN on all switch-to-switch links.
  C. Enable IP authorized managers for the administrator subnet.
  D. Configure IP addressing on OOBM ports and connect them in a dedicated network.
  A. Assign at least one port on each switch to a Virtual Switching Framework (VSF) link and connect those ports in a dedicated network.

• Question 3:

  Refer to the exhibit.

  

  A network administrator connects several new Aruba Instant APs (at factory defaults), as shown in the exhibit. After waiting several minutes for the cluster to form, the administrator is ready to provision the cluster. The administrator wants to be redirected to the Instant UI without the need to know the correct IP address.

  How should the administrator connect the management station to enable access to the virtual controller (VC)?

  A. to a switch port in the same VLAN
  B. directly to one instant AP's second Ethernet port
  C. to the Instant SSID
  D. directly to one Instant AP's Basic Service Set (BSS)
  D. directly to one Instant AP's Basic Service Set (BSS)

• Question 4:

  Which standard for wireless connectivity supports both 2.4GHz and 5GHz?

  A. 802.11a
  B. 802.11ac
  C. 802.11g
  D. 802.11n
  D. 802.11n

• Question 5:

  A network administrator wants to form a cluster with several Aruba Instant APs (IAPs). What must the administrator verify?

  A. that all APs are the same model
  B. that all APs are operating on the same radio channel
  C. that all APs are connected in the same subnet
  D. that all APs are pre-configured with WLANs with the same SSID
  D. that all APs are pre-configured with WLANs with the same SSID

• Question 6:

  A company needs a switch that supports 10GbE and 40GbE for its mid-sized campus. The company prefers stackable, or fixed port, switches over modular switches. Which ArubaOS switch series best meet these needs?

  A. Aruba 2530
  B. Aruba 2930F
  C. Aruba 3810
  D. Aruba 5400R
  B. Aruba 2930F

• Question 7:

  Member 1 is the commander of a Virtual Switching Framework (VSF) fabric. A power disruption causes member1 to go down. What happens when power is restored and member 1 boots?

  A. Member 1 fails to rejoin the VSF fabric, and the error disrupts member 2.
  B. Member 1 rejoins the VSF fabric and becomes the commander.
  C. Member 1 rejoins the VSF fabric, and member 2 continues to act as commander.
  D. Member 1 fails to rejoin the VSF fabric, and member 2 continues to act as commander.
  B. Member 1 rejoins the VSF fabric and becomes the commander.

• Question 8:

  A network administrator wants to use Aruba AirWave to manage Aruba 3810 Series switches deployed at the campus access layer. How does AirWave determine which configuration template to apply to these switches?

  A. based on their group
  B. based on their lowest level subfolder
  C. based on their top level folder
  D. based on the global group associated with their group
  D. based on the global group associated with their group

• Question 9:

  Several servers are connected to an ArubaOS switch. The servers send traffic with 802.1Q VLAN ID 5. How should the network administrator configure the ArubaOS switch to receive this traffic?

  A. Make VLAN 5 the Default VLAN on the switch before the servers connect to their switch ports.
  B. Make switch ports connected to servers untagged members of VLAN 5.
  C. Make switch ports connected to servers tagged members of VLAN 5.
  D. Make VLAN 5 the Primary VLAN on the switch.
  C. Make switch ports connected to servers tagged members of VLAN 5.

• Question 10:

  Refer to the exhibit.

  

  MSTP is enabled on the switches shown in the exhibit.

  Which additional step should the network administrator take to support load sharing of traffic on different switch-to-switch links?

  A. Configure different spanning tree port priorities for different instances on each access layer switch.
  B. Assign different spanning tree port costs to different instances on each access layer switch.
  C. Ensure that half of the switches use config revision 1 and half of the switches use config revision 2.
  D. Create an identical VLAN-to-instance mapping on each switch, in which some VLANs are in each instance.
  A. Configure different spanning tree port priorities for different instances on each access layer switch.