HP HPE6-A41 Online Practice Questions and Exam Preparation

HP HPE6-A41 Online Questions & Answers

• Question 111:

  Refer to the exhibit.

  

  Based on the output shown in this exhibit, which statement is true about the 10.0.0.2 neighbor?

  A. The neighbor rejects communications because it already has its maximum number of neighbors.
  B. The neighbor has mismatched settings and cannot exchange information with this switch.
  C. The neighbor communicates with this switch, but it cannot hold any more routes in its database.
  D. The neighbor communicates with this switch, and they have exchanged all topology information.
  D. The neighbor communicates with this switch, and they have exchanged all topology information.

• Question 112:

  A company has ArubaOS switches that are already configured to support the network. The company now wants to use Aruba AirWave to manage the switches. The network administrator creates a new group on Aruba AirWave, and then

  discovers several ArubaOS switches that should belong to this group.

  What is the best practice for the initial authorization of the switches in AirWave?

  A. Authorize the switches in Monitor + Firmware Updates only mode.
  B. Authorize the switches and immediately change the scan set credentials to match the credentials on the switches.
  C. Authorize the switches and immediately change the global communication settings to match the credentials on the switches.
  D. Authorize the switches in Managed Read/Write mode.
  D. Authorize the switches in Managed Read/Write mode.

• Question 113:

  A network administrator wants to download a configuration from an ArubaOS switch. The administrator does not have local access to the switch and wants to copy the configuration in a secure manner that prevents eavesdroppers from reading the configuration. Which two options can the administrator use to copy the configuration?

  A. SFTP and HTTPS
  B. ZModem and SFTP
  C. HTTPS and TFTP
  D. HTTPS and ZModem
  A. SFTP and HTTPS

• Question 114:

  Refer to the exhibit.

  

  Device 1 needs to send traffic to Device 2, and it sends an ARP request in preparation. Which devices process this ARP request?

  A. all devices in VLAN 2, 192.168.2.0/24 subnet
  B. all devices connected to Switch-2
  C. all devices in VLAN 3, 192.168.3.0/24 subnet
  D. all devices in this network
  A. all devices in VLAN 2, 192.168.2.0/24 subnet

• Question 115:

  Refer to the exhibit.

  

  Based on the exhibit, what is the problem?

  A. An issue causes the spanning tree to converge and re-converge again and again.
  B. Interface 25 on Switch-1 is incorrectly configured as an STP edge port and cause a loop to occur.
  C. Interface 25 on Switch-1 does not support the correct VLANs and prevents the interface from receiving the correct STP role.
  D. Switch-1 and another switch are configured with the same spanning tree priority and cause the root election to occur again and again.
  A. An issue causes the spanning tree to converge and re-converge again and again.

• Question 116:

  Refer to the exhibit.

  

  What should the network administrator do to permit Switch-1 to route traffic from a client in 10.1.11.0/24 to a client in 10.1.12.0/24?

  A. Enable proxy ARP.
  B. Enable IP routing.
  C. Configure a static route to 10.1.11.0/24 and a static route to 10.1.12.0/24.
  D. Enable OSPF routing on VLAN 11 and on VLAN 12 in the same area.
  B. Enable IP routing.

• Question 117:

  Refer to the exhibits. Exhibit 1

  

  Exhibit 2

  

  A network uses RSTP, as shown in the exhibits. The network administrator wants switches to use the link that connects to Core-2 to forward some of the traffic. The administrator enters these commands on every switch shown in the exhibit:

  

  The administrator then discovers that the links to Core-2 still did not forward any traffic. What should the administrator do to enable these links to carry traffic?

  A. Activate the MSTP region configuration on all switches.
  B. Lower the port cost on the links that connect to Core-2 on the access layer switches.
  C. Configure Core-2 with spanning tree priority 0 in instance 2.
  D. Change the spanning tree mode to MSTP on all switches.
  B. Lower the port cost on the links that connect to Core-2 on the access layer switches.

• Question 118:

  Refer to the exhibit.

  

  Originally, all four switches had the same region configuration. VLAN 14 was added to Switch_D and then mapped to instance 2. How does this affect the MSTP topology?

  A. Load sharing is lost, one of the uplinks is blocked for all traffic on Switch_C and Switch_D.
  B. Load sharing is lost, one of the uplinks is blocked for all traffic on Switch_D
  C. All connectivity is lost, both uplinks are blocked on Switch_D.
  D. A Layer 2 loop exists and will cause sporadic connectivity issues.
  B. Load sharing is lost, one of the uplinks is blocked for all traffic on Switch_D

• Question 119:

  Which technology enables a network administrator to group users by logical function instead of physical location, reduce bandwidth waste by limiting broadcast traffic, and improve security by isolating users at Layer2?

  A. 802.1X
  B. SNMPv3
  C. VLANs
  D. Virtual Switching Framework (VSF)
  D. Virtual Switching Framework (VSF)

• Question 120:

  Which settings should match on physical interfaces before a network combines them in a link aggregation?

  A. speed and duplex mode
  B. DSCP and media
  C. speed and VLANs
  D. LLDP TLVs and VLAns
  A. speed and duplex mode