HP HPE6-A41 Online Practice Questions and Exam Preparation

HP HPE6-A41 Online Questions & Answers

• Question 61:

  What is one advantage of OSPF over static routing?

  A. OSPF allows ArubaOS switches to use default routes, while static routes cannot use 0.0.0.0/0 as the destination network.
  B. OSPF has a lower default administrative distance than static routing on ArubaOS switches.
  C. OSPF better meets the needs of a complex topology with many redundant routes that static routing.
  D. OSPF permits load sharing traffic over multiple routes, while static routing does not.
  C. OSPF better meets the needs of a complex topology with many redundant routes that static routing.

• Question 62:

  A Virtual Switching Framework (VSF) fabric currently has two members and two physical 10GbE links in its VSF link. Which administrative task can a network administrator perform on this VSF fabric when both members are online?

  A. Remove a VSF member.
  B. Add a new 40GbE link to the VSF link.
  C. Remove one of the physical links in the VSF link.
  D. Change the VSF link to use 40GbE links instead of 10GbE links.
  A. Remove a VSF member.

• Question 63:

  A network administrator wants to place desktops connected to an ArubaOS switch in VLAN5. The desktops have no awareness of VLANs. How should the administrator assign desktops to the VLAN?

  A. Make switch ports connected to desktops tagged members of VLAN5.
  B. Make VLAN5 the Default VLAN on the switch before the desktops connect to the switch ports.
  C. Make VLAN5 the Primary VLAN on the switch.
  D. Make switch ports connected to desktops untagged members of VLAN5.
  D. Make switch ports connected to desktops untagged members of VLAN5.

• Question 64:

  Refer to the exhibit. Exhibit 1.

  

  Exhibit 2.

  

  The administrator enters the show spanning-tree instance 2 command on Switch-3 and sees the output shown in Exhibit 2. What could explain the output results?

  A. Switch-1 has a lower MAC address than Switch-2.
  B. Switch-1 has a higher MAC address than Switch-2.
  C. Switch-3 filters BPDUs on port 26.
  D. Switch-3 has incompatible MSTP region settings with other switches.
  D. Switch-3 has incompatible MSTP region settings with other switches.

• Question 65:

  Refer to the exhibit.

  

  All of the switches shown in the exhibit are ArubaOS switches.

  Where should the network administrator configure an IP helper address of 10.1.1.10?

  A. on VLAN 2 on Switch-1
  B. on VLAN 2 on Switch-3
  C. on VLAN 1 on Switch-1
  D. on VLAN 1 on Switch-2
  A. on VLAN 2 on Switch-1

• Question 66:

  A network administrator wants to disable physical interfaces 13-24 on an ArubaOS switch. How can the administrator do this?

  A. Assign the range of interfaces to a VLAN. Then, disable the VLAN.
  B. Create a named range for interfaces 13-24. Then, disable the named range.
  C. Create a named port group for interfaces 13-24. Then, disable the named port group.
  D. Use the interface disabl command. Specify 13-24 for the ID.
  D. Use the interface disabl command. Specify 13-24 for the ID.

• Question 67:

  A network administrator needs to configure a link aggregation on an ArubaOS switch.

  For which type of link aggregation is the administrator required to enter the lacp command in the interface context?

  A. a distributed LACP link aggregation
  B. a dynamic LACP link aggregation
  C. a static LACP link aggregation
  D. a manual LACP link aggregation
  B. a dynamic LACP link aggregation

• Question 68:

  A network administrator discovers and then authorizes several ArubaOS switches in Aruba AirWave. Immediately after the administrator authorizes the switches, AirWave cannot communicate with the switches anymore. What should the administrator do to restore communication?

  A. Change the SNMP and Telnet/SSH credentials in the AirWave global communication settings to match those on the switches.
  B. Change the management level for the switches to Monitoring and Firmware Updates Only.
  C. Specify the SNMP and Telnet/SSH credentials on the switches to update the individual communication settings on the switches.
  D. Change the management level for the switches to Manage Read/Write.
  C. Specify the SNMP and Telnet/SSH credentials on the switches to update the individual communication settings on the switches.

• Question 69:

  A company requires switches to use MSTP instead of RSTP, so that the switches can forward traffic on more than one switch-to-switch link. How does the administrator set up the solution to meet this requirement?

  A. Set the same spanning tree cost on all redundant links on a switch.
  B. Ensure that switches use the 802.3t standard costs instead of the legacy costs.
  C. Map different VLANs to different instances, and make a different switch root bridge in each instance.
  D. Configure every switch with a unique bridge propriety in the IST, which is also called spanning tree instance 0.
  C. Map different VLANs to different instances, and make a different switch root bridge in each instance.

• Question 70:

  Refer to the exhibit.

  

  A network administrator logs in to the CLI of a Virtual Switching Framework (VSF) fabric and enters the command shown in the exhibit. What does the output reveal?

  A. MAD assistant at 10.1.0.2 failed to respond to probe requests.
  B. The VSF link failed, and MAD shut down the links on the other member.
  C. MAD is configured incorrectly and causes a split brain situation to occur.
  D. The VSF link failed, and MAD shut down the links on this switch.
  B. The VSF link failed, and MAD shut down the links on the other member.