HP HPE6-A41 Online Practice Questions and Exam Preparation

HP HPE6-A41 Online Questions & Answers

• Question 91:

  Refer to the exhibit.

  

  Spanning tree runs on the switches shown in the exhibit. The network administrator enters these two commands: Switch-1(config)# spanning-tree priority 0 Switch-2(config)# spanning-tree priority 1

  The other switches use the default spanning tree priorities. The administrator enters the show spanning-tree command on Switch-2.

  If the configuration is correct, which roles will the output show?

  A. A1 = Designated A2 = Alternate A3 = Alternate
  B. A1 = Root A2 = Designated A3 = Designated
  C. A1 = Designated A2 = Designated A3 = Designated
  D. A1 = Root A2 = Alternate A3 = Alternate
  B. A1 = Root A2 = Designated A3 = Designated

• Question 92:

  A network administrator prepares an ArubaOS switch to be monitored and managed by AirWave. Which credentials are required for AirWave to change configuration settings on the switch?

  A. RADIUS shared secret
  B. SNMPv2c community with manager unrestricted privileges
  C. Telnet or SSH password
  D. SNMPv3c user in the ManagerPriv group
  A. RADIUS shared secret

• Question 93:

  Refer to the exhibit.

  

  The student A client needs to connect to FTP Server B. Student A sends the necessary ARP request and receives a reply. Which destination MAC address does the Student A client use in the FTP packet to FTP Server B?

  A. 00-1D-B3-F1-EF-40
  B. 00-E0-52-F0-44-87
  C. 00-1D-B3-F1-EF-31
  D. 00-E0-52-F0-41-B2
  A. 00-1D-B3-F1-EF-40

• Question 94:

  An ArubaOS switch operates at factory default settings. A network administrator enters this command: Switch (config)# password operator plaintext mysecret

  How does the switch now control access to the CLI through the console port?

  A. It forces users to enter no username and password operator to gain access to basic mode. Users must then enter password mysecret to reach enable mode.
  B. It forces users du enter username operator and password mysecret to gain access to basic mode. Users can then reach enable mode without authenticating.
  C. It allows users to access basic mode without logging in, but forces them to enter password mysecret to reach enable mode.
  D. It forces users to enter no username and password mysecret to gain access to basic mode. Users can then reach enable mode without authenticating.
  C. It allows users to access basic mode without logging in, but forces them to enter password mysecret to reach enable mode.

• Question 95:

  A network administrator just received two switches and wants to use the plug-and-play method to establish a Virtual Switching Framework (VSF) fabric with the fewest steps possible. What must the administrator do to establish the fabric in this way?

  A. Configure a VSF link on the commander, and enable VSF on the standby member.
  B. Configure a VSF link on the commander, and enable VSF on the commander.
  C. Enable VSF on both me commander and the standby member.
  D. Configure a VSF link on both the commander and the standby member.
  B. Configure a VSF link on the commander, and enable VSF on the commander.

• Question 96:

  A network administrator creates a local user account and assigns that account to the Level-9 authorization group. The administrator tests the group assignment and is able to successfully log in with the local user credentials. However, the administrator is able to enter all the commands rather than only the commands permitted by the Level-9 group.

  How can the administrator resolve this issue?

  A. Set an operator password.
  B. Set the command access level to enable.
  C. Set the command access level to all.
  D. Set command authorization to local.
  D. Set command authorization to local.

• Question 97:

  An ArubaOS switch operates at its factory default settings. A network administrator connects the switch to a VLAN with a DHCP server. The switch-to-switch connection carries untagged traffic. The administrator wants to use Telnet log in to the switch CLI.

  How should the administrator contact the switch and log in?

  A. Contact the switch at its default IP address 172.16.0.254/24 and log in without entering a password.
  B. Contact the switch at its default IP address 192.168.1.1/24 and log in with me default password admin.
  C. Contact the switch at its DHCP-assigned IP address and log in without entering a password.
  D. Contact the switch at its DHCP-assigned IP address and log in with the default password aruba.
  C. Contact the switch at its DHCP-assigned IP address and log in without entering a password.

• Question 98:

  A company has a single routing protocol environment.

  What is one reason to use OSPF routing instead of static routing?

  A. OSPF allows ArubaOS switches to use default routes, while static routes cannot use 0.0.0.0/0 as the destination network.
  B. OSPF has a lower default administrative distance than static routing on ArubaOS switches.
  C. OSPF reduces the risk of accidentally introducing routing loops, while static routing does not.
  D. OSPF permits load sharing traffic over multiple routes, while static routing does not.
  C. OSPF reduces the risk of accidentally introducing routing loops, while static routing does not.

• Question 99:

  A company needs a switch that supports 10GbE and 40GbE for its mid-sized campus. The company prefers stackable, or fixed port, switches over modular switches. Which ArubaOS switch series best meet these needs?

  A. Aruba 2530
  B. Aruba 2930F
  C. Aruba 3810
  D. Aruba 5400R
  B. Aruba 2930F

• Question 100:

  A network administrator is in this context in an ArubaOS switch CLI:

  Switch (vlan10)#

  The administrator wants to leave the configuration context with a single command/

  Which command should the administrator enter?

  A. logout
  B. quit
  C. exit
  D. end
  B. quit