HP HPE6-A41 Online Practice Questions and Exam Preparation

HP HPE6-A41 Online Questions & Answers

• Question 71:

  Member 1 is the commander of a Virtual Switching Framework (VSF) fabric. A power disruption causes member1 to go down. What happens when power is restored and member 1 boots?

  A. Member 1 fails to rejoin the VSF fabric, and the error disrupts member 2.
  B. Member 1 rejoins the VSF fabric and becomes the commander.
  C. Member 1 rejoins the VSF fabric, and member 2 continues to act as commander.
  D. Member 1 fails to rejoin the VSF fabric, and member 2 continues to act as commander.
  B. Member 1 rejoins the VSF fabric and becomes the commander.

• Question 72:

  Refer to the exhibit. Exhibit 1.

  

  Exhibit 2.

  

  Assume that Switch-2 is correctly configured for OSPF.

  Which additional step must the administrator take to enable Switch-1 to advertise 192.168.2.0/24 to Switch-2?

  A. Set a router ID on Switch-1.
  B. Configure a route to advertise 192.168.2.0/24 on Switch-1.
  C. Add Switch-2's router ID to Switch-1's OSPF neighbor list.
  D. Enable OSPF on VLAN 2.
  D. Enable OSPF on VLAN 2.

• Question 73:

  What is true about the community string used for SNMPv1 and SNMPv2c?

  A. The community string hashes the SNMP message, but does not encrypt it, which provides for data integrity.
  B. The community string is like a password transmitted in cleartext, which provides no data integrity or privacy.
  C. The community string encrypts the SNMP message, but does not hash it, which provides for data privacy.
  D. The community string encrypts and hashes the SNMP message, which provides for data integrity and privacy.
  B. The community string is like a password transmitted in cleartext, which provides no data integrity or privacy.

• Question 74:

  Refer to the exhibit.

  

  Which issue could cause the Blocked status on A2?

  A. A1 and A2 are connected to different switches.
  B. A1 and A2 use different trunk load balancing modes.
  C. A1 and A2 support different VLANs.
  D. A1 and A2 have spanning tree enabled on the link aggregation.
  D. A1 and A2 have spanning tree enabled on the link aggregation.

• Question 75:

  A network administrator wants to form a cluster with several Aruba Instant APs (IAPs). What must the administrator verify?

  A. that all APs are the same model
  B. that all APs are operating on the same radio channel
  C. that all APs are connected in the same subnet
  D. that all APs are pre-configured with WLANs with the same SSID
  D. that all APs are pre-configured with WLANs with the same SSID

• Question 76:

  A company has two ArubaOS switches, Switch1 and Switch2. Switch1 will be the commander for a new Virtual Switching Framework (VSF) fabric. Switch2 is a new switch that will be the standby member. The network administrator wants to configure the proper settings on the standby member interface before the standby member joins the fabric.

  What should the administrator do before the switches are joined in the VSF fabric?

  A. Configure the interface settings on Switch2. Then enable VSF on Switch2.
  B. Enable VSF on Switch2. Then configure the interface settings on Switch2.
  C. Provision member2 on Switch1. Then configure the member2 interface settings on Switch1.
  D. Provision member2 on Switch1 and member1 on Switch2. Then configure the member2 interface settings on Switch2.
  D. Provision member2 on Switch1 and member1 on Switch2. Then configure the member2 interface settings on Switch2.

• Question 77:

  Member1 is the commander of a Virtual Switching Framework (VSF) fabric. A power distribution causes member 1 to go down. Now the network administrator wants to rejoin member1 to the VSF fabric and make member1 the commander again.

  What should the administrator do?

  A. Boot member1 and allow it to rejoin to the VSF fabric. Then reboot member2.
  B. Boot member1 and allow it to rejoin the VSF fabric.
  C. Disconnect member1 from member2 before booting member1.
  D. Configure member2 with VSF priority0. Then boot member1 and allow it to rejoin the VSF fabric.
  D. Configure member2 with VSF priority0. Then boot member1 and allow it to rejoin the VSF fabric.

• Question 78:

  How many operating system image files can a network administrator load on an ArubaOS switch?

  A. two
  B. three
  C. four
  D. unlimited
  A. two

• Question 79:

  A network administrator needs to complete the initial setup on an ArubaOS switch with the use of remote access. How can the network administrator do this?

  A. Connect the switch's OOBM port to the same VLAN as the management station, and then establish a Telnet session to the switch default IP address.
  B. Connect the switch's OOBM port to the same VLAN as Aruba AirWave. Then manually discover the switch in AirWave using the switch default IP address.
  C. Send a Reverse ARP from the management station and assign a temporary IP to the workstation.
  D. Set up the network DHCP server to assign the switch a reserved IP address. Connect the switch to a VLAN with DHCP services and then establish a Telnet session to the reserved IP address.
  B. Connect the switch's OOBM port to the same VLAN as Aruba AirWave. Then manually discover the switch in AirWave using the switch default IP address.

• Question 80:

  Refer to the exhibit.

  

  The network consists of two ArubaOS switches with routing disabled.

  How should the network administrator configure the link between Switch A and Switch B to ensure that all hosts can communicate to all the other hosts within their respective VLANs?

  A. tagged for VLAN 20 and tagged for VLAN 30
  B. untagged for VLAN 10 and tagged for VLAN 30
  C. tagged for VLAN 10 and tagged for VLAN 20
  D. untagged for VLAN 10, untagged for VLAN 20, and tagged for VLAN 30
  C. tagged for VLAN 10 and tagged for VLAN 20