HP HP0-Y52 Online Practice Questions and Exam Preparation

HP HP0-Y52 Online Questions & Answers

• Question 51:

  On an HP Comware switch, which view must an administrator access in order to execute the debug command?

  A. Manager
  B. Operator
  C. System
  D. User
  D. User

• Question 52:

  An HP switch learns identical valid routes with different protocols. How does the switch choose which route to add to its IP routing table?

  A. It adds the route with the highest administrative distance, or route preference.
  B. It adds the route with the highest cost.
  C. It adds the route with the lowest cost.
  D. It adds the route with the lowest administrative distance, or route preference.
  D. It adds the route with the lowest administrative distance, or route preference.

• Question 53:

  Refer to the exhibit.

  

  An HP Comware switch is using its default user-interface settings. The network administrator then enters the commands shown in the exhibit. What correctly describes how an admin user must now log in?

  A. When the admin user logs in to the console port, the admin user must enter either a password of password1 or password2.
  B. When the admin user logs in using Telnet, the admin user must enter either a password of password1 or password2.
  C. When the admin logs in using Telnet, the admin user must enter a password of password1 and is given level 1 privileges.
  D. When the admin user logs in to the console port, the admin user must enter a password of password1 and is given level 3 privileges.
  D. When the admin user logs in to the console port, the admin user must enter a password of password1 and is given level 3 privileges.

• Question 54:

  A network administrator wants to disable physical interfaces 13-24 on an HP ProVision switch. How can the administrator do this?

  A. Create a named port group for interfaces 13-24. Then disable the named port group.
  B. Use the interface disable command. Specify 13-24 for the ID.
  C. Assign the range of interfaces to a VLAN. Then, disable the VLAN.
  D. Create a named range for interfaces 13-24. Then, disable the named range.
  D. Create a named range for interfaces 13-24. Then, disable the named range.

• Question 55:

  Which credential is required to validate SNMPv2c write requests?

  A. Community string
  B. Scheme
  C. MD5 authkey
  D. AAA authentication
  A. Community string

• Question 56:

  Refer to the exhibit.

  

  A network administrator sets up OSPF in part of the network topology shown in the exhibit. The Comware-1 switch is already configured. The administrator needs to configure ProVision-1 so that:

  -OSPF includes VLANs 10 and 20 in the routing process.

  -The router ID of 1.1.1.1 is assigned to the switch.

  -

  The ProVision-1 switch can successfully build a neighbor adjacency with the Comware-1 switch. Which configuration should the administrator apply to the ProVision-1 switch to meet these requirements?

  A. router-id 1.1.1.1router ospf area 0vlan 10ip ospf area 0vlan 20ip ospf area 0
  B. router ospf router-id 1.1.1.1area 0 vlan 10area 0 vlan 20enable
  C. router ospfrouter-id 1.1.1.1area 0 vlan 10area 0 vlan 20
  D. ip router-id 1.1.1.1router ospfarea 0enablevlan 10 ip ospf area 0vlan 20 ip ospf area 0
  D. ip router-id 1.1.1.1router ospfarea 0enablevlan 10 ip ospf area 0vlan 20 ip ospf area 0

• Question 57:

  Refer to the exhibit.

  

  Which endpoint or endpoints receive broadcast ARP requests sent by EndpointA?

  A. EndpointB, EndpointC, and EndpointD
  B. EndpointB only
  C. EendpointB and EndpointC only
  D. EndpointC only
  D. EndpointC only

• Question 58:

  A customer is implementing a network using HP ProVision switches. Which default setting applies to the ProVision switches?

  A. All ports are disabled.
  B. Routing is enabled.
  C. Telnet is enabled.
  D. A static IP address is assigned to VLAN 1.
  C. Telnet is enabled.

• Question 59:

  A network administrator wants to establish an LACP link aggregation between an HP Comware switch and an HP ProVision switch. Which settings should the administrator configure?

  A. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to lacp.
  B. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to trunk.
  C. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to trunk.
  D. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to lacp.
  D. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to lacp.

• Question 60:

  What is one difference between Network Segment-based discovery and ARP-based discovery on HP Intelligent Management Center (IMC)?

  A. With Network Segment-based discovery, network device SNMP settings must match SNMP settings on IMC. With ARP-based discovery, only ARP settings must match.
  B. With Network Segment-based discovery, IMC can discover multiple devices. With ARP- based discovery, IMC can only discover one device; the administrator must re-run ARP- based discovery to discover a second device.
  C. With Network Segment-based discovery, the administrator enters a range of IP addresses to discover. With ARP-based discovery, the administrator enters one seed IP address, and IMC dynamically learns more IP addresses to discover.
  D. With Network Segment-based discovery, IMC can discover Layer 3 devices. With ARP- based discovery, IMC can discover only Layer 2 devices.
  C. With Network Segment-based discovery, the administrator enters a range of IP addresses to discover. With ARP-based discovery, the administrator enters one seed IP address, and IMC dynamically learns more IP addresses to discover.