HP HP Certifications HP0-Y52 Questions & Answers

• Question 101:

  Refer to the exhibits.

  Exhibit 1

  

  Exhibit 2

  

  All of the switches in Exhibit 1 are routing switches. Exhibit 2 shows the routes configured on these switches. The direct (connected) routes are not shown, but assume that links are configured with the IP addresses shown in Exhibit 1. The network administrator wants to protect communications between clients and servers in case Link 1 fails. What should the administrator do to protect these communications in this failover situation?

  A. Add a redundant route to 10.1.10.0/24 on Switch-4 and a redundant route to 10.1.20.0/24 on Switch-1.

  B. Add a redundant route to 10.1.20.0/24 on Switch-1 and a redundant route to 10.1.20.0/24 on Switch-2.

  C. Add a redundant route to 10.1.10.0/24 on Switch-1 and a redundant route to 10.1.20.0/24 on Switch-4.

  D. Add a redundant route to 10.1.20.0/24 on Switch-1 and a redundant route to 10.1.10.0/24 on Switch-2.

  Correct Answer: A

• Question 102:

  Which FlexNetwork architecture component provides high performance and low-latency for virtual and physical servers that provide services to the users in a company?

  A. FlexFabric

  B. FlexDataCenter

  C. FlexNet

  D. FlexArchitecture

  Correct Answer: A

• Question 103:

  Which privilege level would a network administrator use to configure an HP ProVision switch?

  A. Super

  B. User

  C. Manager

  D. Administrator

  Correct Answer: C

• Question 104:

  Refer to the exhibit.

  

  The network administrator is setting up Multiple Spanning Tree Protocol (MSTP) with the settings shown in the exhibit. All the switches are in the same region. The administrator has requested help determining which VLANs each switch-toswitch link should carry. What is a recommendation for this topology?

  A. To prevent disruptions during link failure, Links 1-4 should carry VLANs 10-13.

  B. To optimize forwarding, Links 1 and 2 should only carry VLANs 10 and 12, and Links 3 and 4 should only carry VLANs 11 and 13.

  C. To ensure compatibility with MSTP, Links 1-4 should be untagged in VLAN 1 and have no tagged VLAN assignments.

  D. To optimize forwarding, Links 1 and 3 should only carry VLANs 10 and 11, and Links 2 and 4 should only carry VLANs 12 and 13.

  Correct Answer: D

• Question 105:

  A network administrator examines an HP Comware switch that is configured to route packets between VLANs. The switch is configured with multiple routing protocols. All routing protocols have learned of the same destination network. All routing protocols use the default administrative distances.

  Which routing protocol does the switch select for the destination network?

  A. EIGRP

  B. Indirect

  C. OSPF

  D. Static route

  Correct Answer: C

• Question 106:

  Refer to the exhibit.

  Exhibit: Network diagram and routing tables

  

  Why does traffic from PC1 fail to reach PC2?

  A. Only static routes have been enabled

  B. The subnet mask is incorrect on the routers

  C. There is no route back from router B

  D. A default gateway setting is incorrect

  Correct Answer: C

• Question 107:

  Which HP device or port type can modify, read, and respond with frames that include 802.1Q VLAN tags?

  A. Comwaretrunk ports

  B. Comwareroute-mode ports

  C. ProVisionloopback ports

  D. ProVisionuntagged ports

  Correct Answer: A

• Question 108:

  A mid-sized company purchases HP Intelligent Management (IMC) to manage 500 nodes. In addition to the base platform, the company purchases the UAM, WSM, and NTA modules. Which deployment method should this company use to install their IMC base platform and modules?

  A. Stand-alone

  B. Distributed

  C. Centralized

  D. Hierarchical

  Correct Answer: B

• Question 109:

  A network administrator wants to establish an LACP link aggregation between an HP Comware switch and an HP ProVision switch. Which settings should the administrator configure?

  A. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to lacp.

  B. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to trunk.

  C. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to trunk.

  D. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to lacp.

  Correct Answer: D

• Question 110:

  Refer to the Exhibit. Exhibit: HP Comware switch configuration. [Comware] vlan 100 [Comware-vlan100] quit [Comware] vlan 200 [Comware-vlan200] quit [Comware] interface g1/0/22 [Comware-GigabitEthernet1/0/22] port link-type trunk [Comware-GigabitEthernet1/0/22] port trunk permit vlan 100 200 [Comware-GigabitEthernet1/0/22] quit A network administrator configures the Comware switch, as shown in the exhibit. The network administrator then connects a cable from the Comware's g1/0/22 interface to port 5 on an HP ProVision switch. Which configuration will

  successfully establish connection for VLAN 1, 100, and 200 between the two switches?

  A. ProVision (config) # vlan 100ProVision (config) # vlan 200ProVision (config) # vlan 100 tagged 5ProVision (config) # vlan 200 tagged 5

  B. ProVision (config) # vlan 100ProVision (config) # vlan 200ProVision (config) # interface 5 tagged 100 200

  C. ProVision (config) # vlan 100ProVision (config) # vlan 200ProVision (config) # interface 5 tagged 100ProVision (config) # interface 5 tagged 200

  D. ProVision (config) # vlan 100 200ProVision (config) # vlan 100 200 tagged 5

  Correct Answer: A