HP HP0-Y52 Online Practice Questions and Exam Preparation

HP HP0-Y52 Online Questions & Answers

• Question 41:

  A network administrator is configuring a static route. What should the administrator use as the next hop address?

  A. the IP address on the local interface that is used to egress traffic towards its destination
  B. the lowest IP address on the neighboring router in the path towards its destination
  C. the IP address on the connected interface of a neighboring router in the path towards its destination
  D. the IP address of the default gateway in the destination subnet
  C. the IP address on the connected interface of a neighboring router in the path towards its destination

• Question 42:

  Which settings enable a network administrator to use terminal emulation software to interface with an HP Comware switch's auxiliary port?

  A. 9600 bps, 7 data bits, 1 stop bit, no parity, flow control
  B. 14,200 bps, 8 data bits, 1 stop bit, parity, flow control
  C. 9600 bps, 8 data bits, 1 stop bit, no parity, no flow control
  D. 9600 bps, 8 data bits, 1 stop bit, parity, flow control
  C. 9600 bps, 8 data bits, 1 stop bit, no parity, no flow control

• Question 43:

  A network administrator deletes old files in the flash file system of an HP Comware switch. The administrator then notices that the amount of free space available has not changed. Which command must the administrator execute to free up the space from deleted files?

  A. reset recycle-bin
  B. recycle-bin cleanup
  C. cleanup recycle-bin
  D. recycle-bin empty
  A. reset recycle-bin

• Question 44:

  Match the description with the 802.11 standard. (Each option may be used only once.)

  Hot Area:

  

  

• Question 45:

  A company needs a two-member Intelligent Resilient Framework (IRF) virtual switch. The network administrator is configuring IRF member 2 that will connect to port 1/1 on IRF member 1. What is the correct IRF port ID for member 2?

  A. 1/2
  B. 2/2
  C. 1/1
  D. 2/1
  B. 2/2

• Question 46:

  Refer to the exhibit.

  Exhibit: HP Comware switch configuration

  

  Based on the exhibit output, which type of link aggregation is this?

  A. dynamic trunk protocol
  B. static trunking
  C. dynamic port group
  D. static LACP
  C. dynamic port group

• Question 47:

  Which ProVision configuration includes 10.0.3.0/24, which represents VLAN 30 in OSPF area 0?

  A. vlan 30 ip ospf area 0
  B. vlan 30 area 0
  C. interface vlan 30 ip ospf area 0
  D. router ospf area 0 vlan 30
  A. vlan 30 ip ospf area 0

• Question 48:

  Where is priority information stored in an Ethernet frame?

  A. 802.1Q VLAN tag
  B. IP Precedence field
  C. DSCP field
  D. TOS tag
  A. 802.1Q VLAN tag

• Question 49:

  What is one difference between the 802.11g and 802.11n standards?

  A. 802.11g can operate on the 5Ghz band.
  B. 802.11n can operate on the 2.4Ghz band.
  C. 802.11n supports multiple spatial streams with MIMO.
  D. 802.11g supports channel bonding of multiple channels.
  C. 802.11n supports multiple spatial streams with MIMO.

• Question 50:

  A network administrator enters this command on an HP ProVision switch with IP routing enabled:

  ip route 0.0.0.0/0 10.1.1.1 metric 10 distance 10

  This is the only IP route to 0.0.0.0/0 on the switch. What is the effect?

  A. The switch uses this route for all traffic that does not match a specific route in its routing table.
  B. The switch uses this route for all traffic unless the traffic matches a route with a lower administrative distance than 10.
  C. The switch uses this route to route all traffic from 10.1.1.1.
  D. The switch uses this route for all traffic unless the traffic matches a route with a lower cost than 10.
  C. The switch uses this route to route all traffic from 10.1.1.1.