Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 151:

  A technician is configuring 802.1Q tagging, Virtual Link Aggregation Control Protocol (VLACP) with short timeout, and untagged frames to be discarded. Which part of the network is being configured?

  A. IST
  B. The out-of-band management port
  C. The edge access ports
  D. The uplinks
  D. The uplinks

• Question 152:

  Before enabling IP Source Guard through Device Manager, which two conditions must be met on the system (Choose two)

  A. Dynamic Host control Protocol (DHCP) snooping must be enabled globally
  B. EAPOL must be enabled.
  C. The bsSourceGuardConfigMode MIB object must be removed.
  D. The port is an untrusted DHCP snooping and dynamic ARP Inspection port
  A. Dynamic Host control Protocol (DHCP) snooping must be enabled globally
  D. The port is an untrusted DHCP snooping and dynamic ARP Inspection port

• Question 153:

  When configuring an Ethernet Routing Switch (ERS) 8000 split Multi-Link Trunking (SMLT), protection against an edge switch in the factory default condition must be taken into consideration. Which parameter will help prevent loops on the SMLT ports?

  A. Discarded Untagged Frames
  B. Discard Looped Frames
  C. Spanning Tree Enable
  D. LACP Enable
  A. Discarded Untagged Frames

• Question 154:

  Refer to the exhibit.

  

  Virtual Link Aggregation Control Protocol (VLACP) is configured by port, and traffic is only forwarded across the uplinks when VLCAP is up and running correctly.

  A = InterSwitch Trunk (IST)

  B = SplitMulti-Link Trunk (SMLT)

  #1 ERS 8600 #2 ERS 8600 #3 ERS 4500

  When configuring VLCAP for the network shown in the exhibit, where should it be configured?

  A. On all IST ports and not SMLT ports.
  B. On all SMLT links and one of the IST links.
  C. On all IST and all SMLT ports.
  D. On none of the IST or SMLT links depicted in this network.
  C. On all IST and all SMLT ports.

• Question 155:

  When configuring a new Ethernet Routing Switch (ERS) 8000 using the default interface, the attempt to load an ACLI configuration fails because the default interface is the CLI. How is the ACLI interface obtained?

  A. Change the interface type in the config.cfg file.
  B. Change the ACLI boot flag and save the boot configuration file.
  C. Exit the CLI and choose ACLI at the interface manager prompt.
  D. Use the abort command and enter `no' at the default interface.
  C. Exit the CLI and choose ACLI at the interface manager prompt.

• Question 156:

  The configuration on an ERS 8000 contains a static route, the output from a show ip route info (CLI) command or the routing table output on EDM does not display the destination network configured in the static route. What could be the reason for the remote network not being displayed in the IP routing table?

  A. The remote network is down.
  B. Static routes are not displayed in the routing table.
  C. The next hop address configured in the static route is not reachable.
  D. An accept policy is required to activate static routes.
  C. The next hop address configured in the static route is not reachable.

• Question 157:

  In a unified access solution that supports mobility, the configuration must allow for the creation of mobility tunnels to the remote switch and needs the reservation of a remote switch in mobility solution?

  A. Remote VLANs are dynamically created and will only contain tunnels.
  B. Mobility tunnels are created when needed and mapped to pre-configured existing static VLANs.
  C. Remote VLANS are created with a valid IP address to the tunnel mapping based on the source network.
  D. The remote switch dynamically creates, adds and removes VLANs as required in a mobility solution.
  D. The remote switch dynamically creates, adds and removes VLANs as required in a mobility solution.

• Question 158:

  Routed Split Multi-Link Trunking (RSMLT) is a way to ensure that traffic can be routed off the VLAN adding router redundancy. On which Ethernet Routing Switch (ERS) configuration component is RSMLT configured?

  A. an OSPF protocol
  B. a core switch port
  C. a VLAN
  D. an MLT
  C. a VLAN

• Question 159:

  When configuring an Ethernet Routing Switch (ERS) 8000 redundant installation for warm standby, which protocol is used to give the fastest recalculation of a large layer 3 topology by the Standby CPU, after a Master CPU failure?

  A. STP
  B. RIP
  C. OSPF
  D. BGP
  C. OSPF

• Question 160:

  While configuring packet capture Tool (PCAP), an Ethernet Routing Switch (ERS) 8600 switch has generated the following log:

  pcapAllocateBuffer: malloc(96 Mbs) failed

  Which event could have caused this log, and which course of action resolves the issue?

  A. The memory allocation failed to wrap. Set Pcmcia Wrap to true
  B. The packet capturing stopped. Enable the Buffer-wrap or reset the stats.
  C. The length of the IP frame is too long to capture. Turn on fragmentation
  D. There is not enough available memory for PCAP. Try with a lower value of buffer-size.
  D. There is not enough available memory for PCAP. Try with a lower value of buffer-size.