Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 11:

  You are configuring a QoS Policy on an ERS RS or 8800 module to police the ingress data rate on a port with the following ACLI command on the interface level:

  qos if-policer police-rate 10000.

  What other two ACLI commands are required on the edge interface? (Choose two.)

  A. (config)#interface qos enable.
  B. (config-if)#enable-diffserv enable.
  C. (config-if)#access-diffserv enable.
  D. (config-if)#no core-diffserv enable.
  B. (config-if)#enable-diffserv enable.
  C. (config-if)#access-diffserv enable.

• Question 12:

  An Ethernet Routing Switch (ERS) 8600 is being configured for Virtual Router Redundancy Protocol (VRRP).

  If the default value is used on the peer switch, which CLI command would cause this switch to e the VRRP master?

  A. Config vlan 100 ip vrrp 100 priority 250
  B. Config vlan 100 ip vrrp 100 priority 1
  C. Config vlan 100 ip vrrp 100 master
  D. Config vlan 100 ip vrrp 100 priority master
  A. Config vlan 100 ip vrrp 100 priority 250

• Question 13:

  A customer has purchased some Ethernet Routing Switch (ERS) 5600 switches must integrate two ERS 5600 units into existing stack of ERS 5500 switches. What is the procedure for the integration of the new ERS 5600?

  A. with power applied to the slack, change the existing ERS 5500 base unit to "Non Base Unit" in mixed stack operation Integrate the two new ERS 5600 to the stack with them set as "Base Unit" in mixed stack operation Reboot the stack.
  B. Remove the AC from the stack, integrate the two ERS 5600 units into the existing 5600 set to "base unit" and one ERS 5600 set to "non base unit" set the existing ERS 5500 base unit to "non base unit" apply power to stack.
  C. With power applied to the stack, integrate one ERS into the stack as non base unit in mixed stack operational mode. Change the existing ERS 5500 base unit to "non base unit" and set the new 5600 to "base unit". Reboot the stack integrate the second ERS 5600 in mixed stack operational mode.
  D. With power applied to the stack, integrate one ERS into the stack as non base unit in mixed stack operational mode. After the two ERS 5600 units have obtained their configuration from the ERS 5500 base unit, change the ERS 5500 to "non base unit" and set one ERS 5600 to "base unit". Reboot the switch stack.
  D. With power applied to the stack, integrate one ERS into the stack as non base unit in mixed stack operational mode. After the two ERS 5600 units have obtained their configuration from the ERS 5500 base unit, change the ERS 5500 to "non base unit" and set one ERS 5600 to "base unit". Reboot the switch stack.

• Question 14:

  Which feature should be configured to limit which ports receive multicast streams?

  A. igmp proxy
  B. igmp pruning
  C. igmp snooping
  D. PIM-SM snooping
  C. igmp snooping

• Question 15:

  A technician discovers that an Ethernet Routing Switch (ERS) 8300 cat5e copper link is intermittent. The link connects a distant workstation to 8348GTX port 6/2.

  The cable path is undetermined at this point and it is suspected to traverse many patch panels.

  How can the ERS 8300 Time Domain reflectometer tool be of help in this situation?

  A. The Virtual Circuit Test command config ethernet 6/2 vct test can detect opens, shorts, bad terminations.
  B. The virtual circuit Repair command config ethernet 6/2 vct repair can detect the bad cable pairs and repair the cable by moving data to the good cable pairs.
  C. The Virtual Circuit Echo command config ethernet 6/2 vct echo can detect the bad cable pairs only when connected to another ERS 8300.
  D. The Virtual Circuit Detect command config ethernet 6/2 vct detect can detect how many patch panels are used between the device and switch and provide a percentage of dropped packets.
  A. The Virtual Circuit Test command config ethernet 6/2 vct test can detect opens, shorts, bad terminations.

• Question 16:

  A split Multi-Link Trunking (SMLT) for switch clustering is being configured. Which statement is a configuration requirement for the SMLT?

  A. CP-Limit is configured on edge switch stacks.
  B. Neighboring edge switch stacks should be connected to each other via a DMLT connection to add resilient paths in the event of an SMLT failure.
  C. Alternate the primary path of the SMLT connection to load balance the switch core.
  D. VLANS that are defined on the SMLT are so defined on the MLT that defines the core Inter Switch Trunks (IST)
  D. VLANS that are defined on the SMLT are so defined on the MLT that defines the core Inter Switch Trunks (IST)

• Question 17:

  A technician is configuring password levels on the Ethernet Routing Switch (ERS) 8600, and wants the manager to be able to view and edit most device settings, but not be able to change security and password settings. Which login Level should be set for the manager?

  A. Layer 2 Read Write Access
  B. Layer3Read-WnteAccess
  C. Read Write All Access D. Read-Write Access
  D

• Question 18:

  An Ethernet Routing Switch (ERS) 5000 Series Release 6.2 Is installed in environment.

  

  TO UPGRADE TO A version that includes new features, which statement about licenses is true?

  A. licenses are associated with software releases, not license feature levels.
  B. Remove the old license from the switch and load a new license file
  C. The features designated to the license level are available as soon as the upgrade is completed.
  D. Automatic Unit Replacement (AUR) automatically updates software feature license for any replacement stack unit, except the base unit.
  A. licenses are associated with software releases, not license feature levels.

• Question 19:

  During the installation of the unified access solution, the IP address of the wireless switch interface needs to be configured on the ERS 8000. Which IP address must be used in the configuration?

  A. Any valid IP address within the management VLAN subnet.
  B. Any valid IP address within the unified access VLAN.
  C. The switch CLIP (loopback) address.
  D. Any reachable valid IP address.
  C. The switch CLIP (loopback) address.

• Question 20:

  What does Ping snoop identify?

  A. The path that IP traffic takes over an MLT or SMLT
  B. The rate of IP traffic flow
  C. Which port filter is best to use on MLT networks
  D. Rate limiting for ICMP traffic
  A. The path that IP traffic takes over an MLT or SMLT