Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 141:

  When configuring an Ethernet Routing Switch (ERS) 8600 for Split Multi link Trunking (SMLT). Protection against an edge switch in the factory default condition must be taken into consideration. Which parameter WILL help prevent loops on the SMLT ports?

  A. Discard Untagged Frames
  B. Discard Looped Frames
  C. Spanning Tree Enable
  D. LACP Enable
  A. Discard Untagged Frames

• Question 142:

  A campus network requirement is to introduce Virtual Routing and Forwarding (VRF) in the existing Ethernet Routing Switch (ERS) 8000-based core. The technician has to configure VRF on the ERS 8000. Which statement represents the order for configuring a new VRF?

  A. Create a new VLAN, add an IP address, create a VRF, and move the VLAN to the new VRF.
  B. Create a VRF, add an IP address, create a new VLAN, and move the VLAN to the new VRF.
  C. Create a VRF, create a new VLAN, add an IP address, and move the VLAN to the new VRF.
  D. Create a VRF, create a new VLAN, move the VLAN to the new VRF, and add an IP address.
  D. Create a VRF, create a new VLAN, move the VLAN to the new VRF, and add an IP address.

• Question 143:

  The attempt to manage an Ethernet Routing Switch (ERS) 8600 using a VRRP address was unsuccessful. What is causing this problem?

  A. The fie virtual router identifier is 0.
  B. The datacenter interface is set as a critical IP interface.
  C. A real IP address is required for management access not a VRRP address.
  D. The incorrect MAC offset is configured for the VRRP address.
  C. A real IP address is required for management access not a VRRP address.

• Question 144:

  A technician is configuring 802.1 Q tagging, VLACP with short timeout, untagged frames to be discarded. Which part of the network is being configured?

  A. layer 2 core
  B. layer 3 core
  C. the edge
  D. the uplinks
  D. the uplinks

• Question 145:

  A campus network requirement is to introduce Virtual Routing and Forwarding (VRF) in the existing Ethernet Routing Switch (ERS) 8600-based core. The n has to configure VRF on the ERS 8600. Which statement represents the order for configuring a new VRF?

  A. Create a new VLAN, add an IP address, create a VRF, and move the VLAN to the new VRI
  B. Create a VRF, add an IP address, create a new VLAN, and move the VLAN to the new VRF
  C. Create a VRF, create a new VLAN, add an IP address, and move the VLAN to the new VRF
  D. Create a VRF, create a new VLAN move the VLAN to the new VRF, and add an IP address
  D. Create a VRF, create a new VLAN move the VLAN to the new VRF, and add an IP address

• Question 146:

  An Information Technology organization needs to determine whether they should upgrade their existing Routing Switch (ERS) 8600 switches to release 5.0. Each chassis currently has both 8648GTR 8648TX modules. One of the features that the company requires is the ability to perform port mirroring on multiple ports per module at a time.

  What should be done to meet their port mirroring requirement when upgrading to software release 5.0?

  A. Replace the existing modules with 8648GTRS modules,
  B. Upgrade to ERS 8600 Release 5.0 without any hardware upgrade.
  C. Replace the existing 8648TX modules with ERS 8648TXE for egress mirroring.
  D. Recommend other means to capturing traffic.
  A. Replace the existing modules with 8648GTRS modules,

• Question 147:

  Which statement describes a step in provisioning SPBM in an enterprise network?

  A. Configure IP addresses on the core links.
  B. Enable SPBM and IS-IS globally on all nodes and on the core facing links.
  C. Configure the MAC table.
  D. Configure L2 and L3 VSNs on the core SPBM nodes.
  B. Enable SPBM and IS-IS globally on all nodes and on the core facing links.

• Question 148:

  During the installation of a unified access solution, the IP address of the wireless switch interface needs to be configured on the ERS 8000. Which IP address must be used in configuration?

  A. Any valid IP address within management VLAN subnet.
  B. Any valid IP address within the unified access VLAN subnet.
  C. The switch CLIP (loopback) address.
  D. Any reachable valid IP address.
  C. The switch CLIP (loopback) address.

• Question 149:

  Consider the fallowing port conditions on an Ethernet Routing Switch (ERS) 8648GTRS 10/100/1000 Ethernet I/O module left LED -green Right LED - flashing green. What is the status of the port?

  A. The link speed is 100 Mbps. and the port is disabled.
  B. The link speed is 1000 Mbps, and the port is disabled
  C. The link speed is 100 Mbps. and the port is passing traffic.
  D. The link speed is 1000 Mbps. and the port is passing traffic.
  C. The link speed is 100 Mbps. and the port is passing traffic.

• Question 150:

  To provide load distribution across two or more equal cost paths in a Layer 3 routing environment, the ECMP feature can be used to maximize load sharing. Which two statements correctly describe the ECMP features? (Choose two)

  A. All ECMP next hop addresses are in the routing table
  B. ECMP keeps traffic between two IP addresses on one single path.
  C. All ECMP paths are active and forwarding traffic.
  D. ECMP routes apply to OSPF, RIP and BGP only.
  A. All ECMP next hop addresses are in the routing table
  C. All ECMP paths are active and forwarding traffic.