Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 121:

  A technician is preparing to update an Ethernet Routing Switch (ERS) 550D and needs to see the existing configuration. How is the information to be displayed?

  A. Use the show running-config command.
  B. Use the configuration parameter qualifier.
  C. Use the show alt-modules command.
  D. Use the verbose qualifier.
  A. Use the show running-config command.

• Question 122:

  An existing enterprise network is using Ethernet Routing Switch (ERS) 8600 switches in the campus core. It has determined that 10 Gigabit links are required to ace the existing 1 Gigabit links 1 to the closest. This will affect 18 connections on each of the ERS 8600 switches.

  Which statement describes how to accomplish this requirement in each ERS 8600 chassis?

  A. Replace the two existing switch fabric modules with 8394SF systems.
  B. Replace the two existing switch fabric modules with 8692SF and Supermezz.
  C. Replace the two existing 8616SXE modules with 8612XLRS modules.
  D. Replace the six 8683XLR modules with 8612XLRS.
  C. Replace the two existing 8616SXE modules with 8612XLRS modules.

• Question 123:

  A technician is setting up switch clustering using Split Multi-Link Trunking (SMLT). Which link is configured between the aggregation switches?

  A. Inter-switch trunk
  B. Multi-Link trunk
  C. Split MAC trunk
  D. LAG trunk
  A. Inter-switch trunk

• Question 124:

  Refer to the exhibit.

  

  Based on the command line output shown in the exhibit, how many Gigabit Ethernet ports are available on this Ethernet Routing Switch (ERS) 8600?

  A. 3
  B. 48
  C. 52
  D. 83
  B. 48

• Question 125:

  A technician wants to control the routes being added to the routing table from the BGP routing table. Which statement describes how to do this?

  A. BGP accept filters are applied to all routes from received by BGP peers.
  B. BGP accept filters are applied only to external route information.
  C. BGP accept filters are applied to all incoming and outgoing ports.
  D. BGP adds all new priority routes to the routing table.
  A. BGP accept filters are applied to all routes from received by BGP peers.

• Question 126:

  What is the maximum number of Gigabit Ethernet ports on a single Ethernet Routing Switch (ERS) 8300 Input/Output module?

  A. 16
  B. 24
  C. 48
  D. 50
  C. 48

• Question 127:

  For a Converged campus network, which configuration changes is recommended for the default VLAN (VLAN 1)

  A. Assign an IP address to the default VLAN for switch management.
  B. Remove all port members from default VLAN 1.
  C. Configure QoS on the default VLAN to support voice traffic.
  D. Remove spanning tree from the default VLAN.
  A. Assign an IP address to the default VLAN for switch management.

• Question 128:

  What is a characteristic of Routed Split Multi-Link Trunking (RSMLT) configuration?

  A. RSMLT is only configured on edge SMLT connections.
  B. RSMI T uses priority values to distinguish between the primary and backup routers.
  C. RSMLT routers are implemented with Virtual Routing Forwarding (VRF)-Lite routers.
  D. RSMLT is always used in conjunction with routing protocols and SMLT connections.
  D. RSMLT is always used in conjunction with routing protocols and SMLT connections.

• Question 129:

  The Ethernet routing switch (ERS) 5000 switches are being upgraded and it appears that a license is not recognized on the switch. Which two statements are valid sources of information that will help resolve the license installation? (Choose two.)

  A. Check for an 'invalid license fife' log report
  B. Check the record of MSG address changes
  C. Use the show license command to get the license installation status
  D. Check to see if the MAC address is correct in the license file.
  E. Use the show license file command to get the license installation status.
  C. Use the show license command to get the license installation status
  D. Check to see if the MAC address is correct in the license file.

• Question 130:

  When configuring Single Link Trunking (SLT) or Split Multi-Link Trunking (SMLT), what can be done to facilitate easily adding more VLANs to the network without impacting traffic?

  A. 802.1Q-tag uplinks.
  B. Disable STP on the ports.
  C. Index the ports.
  D. Use redundant MLTs.
  A. 802.1Q-tag uplinks.