Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 131:

  A technician wants to use the New Unit Quick Configuration feature to add new units to a stack of Ethernet Routing Switch (ERS) 5000 switches without. As well as enabling the feature, what else must be done to use the New Unit Quick Communication feature?

  A. Save a template on the base unit
  B. Save a template on the backup unit
  C. Insert a new switch in the stack
  D. Apply the feature license
  C. Insert a new switch in the stack

• Question 132:

  Auto-negotiation should be enabled on all ports except under which condition?

  A. When there is a mix of 10 Mops and 1 Gbps end servers
  B. When there are fiber ports in some end workstations
  C. When only the core Pitches support auto-negotiation
  D. When there is a mix of R and RS modules in the stack
  C. When only the core Pitches support auto-negotiation

• Question 133:

  Consider the following port conditions on an Ethernet Routing Switch (ERS) 8648GTRS 10/100/1000 Ethernet I/O module:

  Left LED green Right LED flashing What is the status of the port?

  A. The link speed is 100 Mbp, and the port is disabled.
  B. The link speed is 1000 Mbps, and the port is disabled.
  C. The link speed is 100 Mbps, and the port is passing traffic.
  D. The link speed is 1000 Mbps, and the port is passing traffic.
  D. The link speed is 1000 Mbps, and the port is passing traffic.

• Question 134:

  Which types of topologies are supported in the implementation of the Avaya Enterprise Fabric? (Choose three)

  A. SPB Layer 2 VSN
  B. SPB GRT shortcuts
  C. SPB GRT 3 VSN
  D. SPBv VSN
  A. SPB Layer 2 VSN
  B. SPB GRT shortcuts
  D. SPBv VSN

• Question 135:

  During a power-on or cold-start sequence, at which stage can he flags to change the operational environment of the switch be set?

  A. boot monitor prompt
  B. image search
  C. PC system test
  D. boot configuration prompt
  A. boot monitor prompt

• Question 136:

  An Ethernet Routing Switch (ERS) 8600 for Virtual Router Redundancy Protocol (VRRP) is being configured. Which CU command would cause this switch to be the VRRP master?

  A. ERS8600:5# config vlan 100 ip vrrp 100 priority 250
  B. ERS8600:5ff config vlan l00 ip vrrp 100 priority 1
  C. ERS860Q:5# config vlan 100 ip vrrp 100 master
  D. ERS8600:5# config vlan 100 ip vrrp 100 priority master
  A. ERS8600:5# config vlan 100 ip vrrp 100 priority 250

• Question 137:

  Fn Ethernet Routing Switch (ERS) 8300 configurations, which service class ensures that protocol updates such as RIP and OSPF are able to get out of a heavily congested switch?

  A. Bronze
  B. Standard
  C. Network Control
  D. Premium Control
  C. Network Control

• Question 138:

  IPFIX is protocol used for the export of flow information from traffic observed on a switch. Which true for the functioning of the IPIX protocol? (Choose two.)

  A. The IPFIX exporter handles sending packets to the collectors.
  B. There is a command for exporting and flushing.
  C. The IPFIX information cannot be exported to a 3rd-party application.
  D. The exporter can support up to 6 collectors
  A. The IPFIX exporter handles sending packets to the collectors.
  B. There is a command for exporting and flushing.

• Question 139:

  One of the switches in the Ethernet Routing Switch (ERS) stacks files and is replaced. The auto unit replacement (AUR) is enabled but the stack is not functioning properly. What is the problem?

  A. The switches in the stack are not identical
  B. the stack power was left on during the switch replacement.
  C. The switches in the stack are not running the same release of software
  D. The stack has two switches with Force Stack disabled.
  B. the stack power was left on during the switch replacement.

• Question 140:

  Not long after bootup of an upgraded Ethernet Routing Switch (ERS) 8310, the system hangs. Which statement describes the cause of this problem?

  A. The CPU module was configured in slot 5.
  B. An ERS 8600 module was configured in the 8300 chassis
  C. The system includes dual 839xSF modules
  D. The system was running in full duplex mode.
  C. The system includes dual 839xSF modules