Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 161:

  Which feature can be used on Split Multi-Link Franking (SMLT) with a SoftDown option?

  A. Extended control packet limit (ext-CP)
  B. Discard untagged frames
  C. Simple Loop Prevention Protocol (SLPP)
  D. Virtual Link Aggregation Protocol (VLACP)
  A. Extended control packet limit (ext-CP)

• Question 162:

  After issuing a show ist stats (CLI) or show ist stat (ACLI) command, it is determined that the running type is normal MLT and not inter Switch Trunks? (Choose two)

  A. The IST is not enabled on the both switches.
  B. The MLT ID does not match on both switches.
  C. The Peer IP address is not the address of the Peer switch IST VLAN.
  D. The peer IP addresses have to be 192.168.1.1/30 and 192.168.1.2/30.
  A. The IST is not enabled on the both switches.
  C. The Peer IP address is not the address of the Peer switch IST VLAN.

• Question 163:

  RSMLT Edge is enabled globally on two ERS 8800 switches. After recovering from a power outage some clients cannot communicate. A technician determined that only one of the core switches has recovered. What should the technician check to ensure that this loss of communication does not occur in the event of a future power outage or other failure?

  A. Turn off the Hold Up timer on both core switches.
  B. Increase the Hold Up Timer to 9999 per VLAN for RSMLT Edge support.
  C. Re-enable RSMLT Edge on each of the VLANs on both switches.
  D. Set the VLAN to copy RSMLT info from a similarly configured VLAN.
  B. Increase the Hold Up Timer to 9999 per VLAN for RSMLT Edge support.

• Question 164:

  When configuring LINK aggregation, a technician created a Distributed Multi-Link Trunk (DMLT) group on the edge connecting switch cluster core. What gets distributed?

  A. Access ports
  B. VLANS
  C. Uplinks
  D. PVIDs
  C. Uplinks

• Question 165:

  A technician is configuring an Ethernet routing switch (ERS)-24T-PWR, and to add ports 10 through 20 to VLAN 100. Which ACLI command is used to accomplish this task?

  A. 5520-24-PWR (config) # vlan members add 100 10-20
  B. 5520-24-PWR (config) # vlan 100 add members 10-20
  C. 5520-24-PWR (config-vlan) # members add 100 10-20
  D. 5520-24-PWR (config-if) #vlan 100 add members 10-20
  A. 5520-24-PWR (config) # vlan members add 100 10-20

• Question 166:

  A customer is upgrading an existing ERS 8610 with the 8692SF to software version 7.x. Which statement regarding the upgrade is correct?

  A. The customer must upgrade the 8692SF to an 8893SF for software release 7.x.
  B. The customer can run 7.x with the existing 8692SF, although some features will be disabled.
  C. The customer can add the SuperMezz module to the 8692SF and run release 7.x.
  D. The customer must upgrade to an ERS 8810 chassis to run software release 7.x.
  C. The customer can add the SuperMezz module to the 8692SF and run release 7.x.

• Question 167:

  A technician needs to reboot an Ethernet Routing Switch (ERS) 5000 Series switch with a default configuration. What needs to be done to keep the IP address and stack license?

  A. Boot partial-default
  B. Boot-default save-license
  C. Boot default-save
  D. Boot restore-license
  A. Boot partial-default

• Question 168:

  By default the ERS 8000 is configured for warm standby. After installation of a new ERS solution with dual CPUs, which three actions need to be Perform on the ERS configuration to ensure high availability mode is enabled and will function correctly? (Choose three)

  A. Set the high availability CPU boot flag to true.
  B. Set the warm standby CPU hoot flag to false.
  C. Set the save to standby CPU boot flag to true.
  D. Save the boot.cfg conflg file and reset the switch to activate the changes.
  E. Install the high availability license file.
  A. Set the high availability CPU boot flag to true.
  D. Save the boot.cfg conflg file and reset the switch to activate the changes.
  E. Install the high availability license file.

• Question 169:

  A technician is configuring Multi Link trunking (SMLT) for an Ethernet routing switch (ERS) 8600 switch cluster. To ensure the fastest possible recovery time, which feature should be avoided?

  A. VLACP
  B. MLT
  C. 802.3 ad
  D. SLPP
  A. VLACP

• Question 170:

  After experiencing issues with XFPs, the show sys pluggable-optical-modules info CLI command is used to find that the switch does not recognize the XFPs. Which other method can be used to view the XFP compatibility?

  A. Check for port alarms.
  B. Show DWDM-XFP {detail}.
  C. Check the config sys set pluggable-optical-module info.
  D. Select Edit, Port, General, DDI/SFP from the Enterprise Device Manager to see the XFP port specifics_
  D. Select Edit, Port, General, DDI/SFP from the Enterprise Device Manager to see the XFP port specifics_