Avaya 3605 Online Practice Questions and Exam Preparation

Avaya 3605 Online Questions & Answers

• Question 111:

  A call centre is using the stacks of Ethernet Routing Switches (ERS) 5520-48T-PWR to supply power over Ethernet (PoE) to their IP telephones. Each switch is attached to 48 telephones. The call centre begins operation at 9:00 am each day and they verify that the switch can supply enough power to support each telephone drawing their maximum power for all switches simultaneously. They are using the IP Phone port 10/100 switch.

  Which statement it is true if all telephones are drawing 13.2 watts simultaneously?

  A. Each switch of supplying full port to all ports with only the AC input
  B. Each switch requires an RPSU 15 in addition to AC to supply full power to all ports.
  C. RPSU 15 can support four ERS 5520 switches that supply full power to all ports.
  D. Each switch can supply full power to all ports while the AC is unavailable if attached to
  B. Each switch requires an RPSU 15 in addition to AC to supply full power to all ports.

• Question 112:

  Based on the command line output shown in the exhibit, how many Gigabit Ethernet ports are available on this Ethernet Routing SwitchlT (ERS) 8600?

  

  A. 16
  B. 24
  C. 26
  D. 28
  A. 16

• Question 113:

  A technician has implemented RSMLT edge design. After recovering from power outage some clients could not communicate. It has been stated that only one of the core RSMLT switches has recovered. What should have been done to prevent the loss of communications?

  A. Turn off the hold down timer.
  B. Increase the hold up timer to 9999.
  C. Clear the peer IP and MAC addresses.
  D. Set the VLAN to copy RSMLT into from a similarity configured VLAN.
  A. Turn off the hold down timer.

• Question 114:

  Which steps are initial steps required to configure the Ethernet Routing Switch (ERS) 8600 in a clustered basic core configuration? (Choose three.)

  A. create VLANs
  B. create the IST
  C. enables OSPF
  D. configure SMLT
  A. create VLANs
  B. create the IST
  D. configure SMLT

• Question 115:

  A technician is implementing a new network that contains eight Ethernet routing switch (ERS) 8600 switches and uses advanced features. Where are two possibilities for generating license? (Choose two)

  A. one individual advanced feature license for each ERS 8600 chassis
  B. one multi-chassis license using multiple MAC addresses
  C. one advanced feature license for the network
  D. one premier feature license for the network
  E. one site license per ERS 8600
  C. one advanced feature license for the network
  E. one site license per ERS 8600

• Question 116:

  What is the front panel port configuration for the Ethernet Routing Switch (ERS) 2550T-PWR?

  A. 48 10/100 BaseT ports (PoE on 48 ports)Two combo 10/100/1000BaseT or SFP port
  B. 48 10/100BaseT ports (PoE on 24 ports)two combo 10/100/1000BaseT or SFP port
  C. 50 10/100BaseT ports (PoE on 25 ports)two combo 10/100/1000BaseT or SFP port
  D. 50 10/100BaseT ports (PoE on 50 ports)two combo 10/100/1000BaseT or SFP port
  B. 48 10/100BaseT ports (PoE on 24 ports)two combo 10/100/1000BaseT or SFP port

• Question 117:

  Which protocol can be used for end-to-end detection in a network as well as for point-to-point detection?

  A. LACP
  B. VLACP
  C. RSTP
  D. MSTP
  B. VLACP

• Question 118:

  In a multicast campus, when should the PIM interface in passive mode be configured?

  A. When the ERS 8600 is used as an edge switch and is aggregating end users
  B. When PIM control traffic must be passed
  C. When there are no unicast routing paths
  D. When more than one multicast routing protocol is in use
  A. When the ERS 8600 is used as an edge switch and is aggregating end users

• Question 119:

  Syslog in the Ethernet Routing Switch (ERS) 8600 allows the mapping of ERS 8600 errors to specified to be specified to the facility local 0-local 7. What is another place of information that syslog provides.

  A. Security level
  B. Message frequency
  C. Syslog table location
  D. System status
  A. Security level

• Question 120:

  OSPF computes the shortest path to destination subnets, whereas, IS-IS, as used with SPMB works differently. Which parameter does IS-IS use to compute the path?

  A. customer MACs
  B. backbone BEB MAC tables
  C. VLAN MAC IDs
  D. backbone nodal MAC addresses
  B. backbone BEB MAC tables