Cisco 350-080 Online Practice Questions and Exam Preparation

Cisco 350-080 Online Questions & Answers

• Question 451:

  What is the use of an "all configurations" backup in Cisco UCS?

  A. Can be used to migrate from a 6120 to a 6140 and retain the same service profiles
  B. Can only be used on the fabric interconnect on which it was created
  C. Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster information
  D. Can be used to match firmware versions between 6120 and 6140 during a migration
  A. Can be used to migrate from a 6120 to a 6140 and retain the same service profiles

• Question 452:

  Which PIM mode is supported in Cisco NX-OS?

  A. sparse mode
  B. dense mode
  C. sparse-dense mode
  D. dense-sparse mode
  A. sparse mode

• Question 453:

  Which command will allow you to display the configured QoS group and the ingress buffer allocated to each QoS group?

  A. show interface priority-flow-control
  B. show interface queuing
  C. show queuing interface
  D. show policy-map system type queuing
  E. show policy-map interface ethernet type queuing
  C. show queuing interface

• Question 454:

  Drag Drop

  Select and Place:

  

  

• Question 455:

  Refer to the exhibit.

  

  Which three levels of protection for the CoPP policy option from the initial setup utility are valid (Choose three.)

  A. lenient
  B. major
  C. none
  D. minor
  E. aggressive
  F. moderate
  A. lenient
  C. none
  F. moderate

• Question 456:

  Refer to the exhibit.

  

  The network administrator is seeing N7K-1 having issues with VLAN 11, and interface VLAN 11 is resetting, causing frequent HSRP state changes. Which two actions would reduce HSRP state changes? (Choose two.)

  A. On N7K-1, configure the HSRP extended hold timer to 180, extending the HSRP hello message hold time.
  B. On N7K-2, configure the HSRP extended hold timer to 180, extending the HSRP hello message hold time.
  C. On N7K-1, configure the pre-empt delay minimum to 180 in order to delay N7K-1 from taking over as the HSRP active router.
  D. On N7K-2, configure the pre-empt delay minimum to 180 in order to delay N7K-2 from taking over as the HSRP active router.
  E. On N7K-2, increase the HSRP priority to 150.
  F. On N7K-2, decrease the HSRP priority to 50.
  C. On N7K-1, configure the pre-empt delay minimum to 180 in order to delay N7K-1 from taking over as the HSRP active router.
  E. On N7K-2, increase the HSRP priority to 150.

• Question 457:

  Which two statements about Cisco Nexus 1000V Series Switches are correct? (Choose two.)

  A. When VSM interfaces are created for a virtual machine, the VMware vSwitch port-group configuration is used initially, which requires the creation of a port-group name for these interfaces and an appropriate VLAN. The simplest configuration is to create a single port group (for example, VSM-Interfaces), that includes all the interfaces that use this port group and the same VLAN.
  B. The mgmt0 interface on the VSM does not necessarily require its own VLAN. In fact, you can use the same VLAN to which the VMware vCenter Server belongs. The VSM management VLAN is really no different from any other virtual machine data VLAN. Alternatively, network administrators can designate a special VLAN for network device management.
  C. Always deploy the Cisco Nexus 1000V Series VSM in pairs, with one VSM that is defined as the primary module and the other that is defined as the secondary module on two separate hosts.
  D. The service console is a critical interface that resides on every logical server.
  B. The mgmt0 interface on the VSM does not necessarily require its own VLAN. In fact, you can use the same VLAN to which the VMware vCenter Server belongs. The VSM management VLAN is really no different from any other virtual machine data VLAN. Alternatively, network administrators can designate a special VLAN for network device management.
  C. Always deploy the Cisco Nexus 1000V Series VSM in pairs, with one VSM that is defined as the primary module and the other that is defined as the secondary module on two separate hosts.

• Question 458:

  Each port that is configured to use LACP has an LACP port priority. Which statements are true about LACP port priority? (Choose three.)

  A. Port priority value can be configured between 1 and 65535.
  B. A higher port priority value means a higher priority of LACP.
  C. Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.
  D. LACP uses the port priority with the port number to form the port identifier.
  E. LACP Port priority default value should always be changed
  A. Port priority value can be configured between 1 and 65535.
  C. Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.
  D. LACP uses the port priority with the port number to form the port identifier.

• Question 459:

  Which option is the advantage of Cisco ACE SSL Offload?

  A. Export cipher suite
  B. Decentralized certificate management
  C. SSL encryption only
  D. Front-end SSL
  D. Front-end SSL

• Question 460:

  Drag Drop

  Select and Place: