Cisco 300-615 Online Practice Questions and Exam Preparation

Cisco 300-615 Online Questions & Answers

• Question 51:

  Refer to the exhibit.

  

  An administrator directly connects a Fibre Channel storage array to ports 1 through 4 on a Cisco UCS 6454 Fabric Interconnect. The administrator configures a service profile to boot directly from the new Fibre Channel storage array, but the service profile fails to boot. When the administrator checks the output of the show flogi database command on the fabric interconnect, it shows the output presented in the exhibit. Which action resolves the issue?

  A. Configure the Zoning Type in vHBA Initiator Group as Multiple Initiator Multiple Target.
  B. Configure the fabric interconnects in Fibre Channel end-host mode.
  C. Configure the Zoning Type in vHBA Initiator Group as Multiple Initiator Single Target.
  D. Configuare the fabric interconnects in Fibre Channel switch mode.
  D. Configuare the fabric interconnects in Fibre Channel switch mode.

  ---

• Question 52:

  An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a "resolve slot" warning. Which server maintenance action resolves the issue?

  A. Perform diagnostic interrupt on the server.
  B. Re-acknowlegement the server.
  C. Reset the server.
  D. Decomission the server.
  B. Re-acknowlegement the server.

  ---

• Question 53:

  A Cisco UCS C-Series Server powers off due to a power outage. The server should turn on when the power is restored with a fixed delay of 3 minutes. However, it remained powered off for more than 3 minutes after the engineer powered it back online. Which two actions resolve the issue? (Choose two.)

  A. Configure the power-restore-policy.
  B. Configure the power restore last-state policy.
  C. Set the delay value to 180.
  D. Set the delay fixed value to 3.
  E. Configure power sync policy.
  B. Configure the power restore last-state policy.
  C. Set the delay value to 180.

  ---

• Question 54:

  Refer to the exhibit.

  

  An engineer must strictly enforce the port security configuration database in the Fibre Channel fabric. A new device has been connected to the Fibre Channel storage interface that was configured for port security. The port security was enabled for the VSAN that the port belongs to. Despite the configuration, the rogue devices can log into the fabric. Which action resolves the issue?

  A. Commit the active database with the port-security database copy vsan 1 command
  B. Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command
  C. Disable CFS distribution with the no port-security distribute vsan 1 command
  D. Commit the changes with the port-security commit copy vsan 1 command
  B. Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command

  ---

• Question 55:

  Refer to the exhibit.

  

  An engineer fails to implement VRRP on a Cisco Nexus 7000 Series Switch. Which action resolves the issue?

  A. Activate the VRRP license.
  B. Configure the VRRP instance globally.
  C. Enable the VRRP feature.
  D. Set the VRRP group number.
  B. Configure the VRRP instance globally.

  ---

• Question 56:

  A network engineer experiences the error "DDR3_P1_B1_ECC" when upgrading Cisco UCS firmware. Which action resolves the issue?

  A. Reset the DIMM
  B. Reset the BMC firmware
  C. Reflash the controller firmware
  D. Reflash the DIMM
  A. Reset the DIMM

  ---

• Question 57:

  An attempt to use a global vNIC redundancy template pair results in a service profile that fails to apply. Which action resolves the issues?

  A. Create the peer names before creating the templates.
  B. Assign the secondary template first, and then set the peer name.
  C. Assign both templates simultaneously.
  D. Assign the primary template first, and then set the peer name.
  D. Assign the primary template first, and then set the peer name.

  ---

• Question 58:

  

  Refer to the exhibit. The script must show the running configuration of interfaces eth1/1 to eth1/3. However, only a subset of interfaces is displayed when the script is run. Which configuration must be changed on line 2 of the script to resolve the problem?

  A. n=-1
  B. n=1
  C. n=-2
  D. n=0
  D. n=0

  ---

• Question 59:

  Refer to the exhibit.

  

  A network engineer deploys scripts to the guest shell of a Cisco Nexus switch. The scripts fail to operate properly due to the limited CPU and file system resources that are assigned by default to the guest shell. The engineer allocated more memory and disk space to the guest shell, but the application continues to fail. Which action resolves the issue?

  A. Disable and enable bash shell
  B. Reboot the guest shell
  C. Redeploy the bash shell
  D. Upgrade the guest shell
  B. Reboot the guest shell

  ---

  https://www.ciscolive.com/c/dam/r/ciscolive/us/docs/2018/pdf/BRKDCN-2015.pdf

• Question 60:

  An engineer configures FCoE between a set of ESXi hosts and a Cisco Nexus 5000 Series Switch. The Converged Network Adapter of the host fails to receive the response from the Cisco Nexus device. Also, the VFC interface is in a down state and the FIP adapter fails to receive 802.1q tagged frames. The host interface is configured for VLAN trunking. Which action resolves the issue?

  A. Activate the reception of Xoff pause frames from the server
  B. Configure the UF link as a spanning-tree edge port
  C. Enable the active STP port state on the bound Ethernet interface
  D. Set the bound Ethernet trunk interface to non-FCoE native VLAN
  D. Set the bound Ethernet trunk interface to non-FCoE native VLAN

  ---