Cisco 300-615 Online Practice Questions and Exam Preparation

Cisco 300-615 Online Questions & Answers

• Question 71:

  Refer to the exhibit.

  

  An engineer must save the running configuration to startup-config and generate a syslog message indicating that the configuration was modified, but an error was received. Which action resolves the issue?

  A. Change the syslog action number to 1.
  B. Use the extended command copy running-config startup-config.
  C. Add event-default as a second action of the EEM script.
  D. Save the configuration using a user with network-admin role.
  C. Add event-default as a second action of the EEM script.

  ---

• Question 72:

  Refer to the exhibit.

  

  The vPC between switch1 and switch2 does not work. Which two actions resolve the problem? (Choose two.)

  A. Configure the IP address on the interface.
  B. Activate VLANs on the vPC.
  C. Configure one of the switches as primary for the vPC.
  D. Correct the configuration of the vPC peer link and the vPC peer keepalive.
  E. Match the vPC domain ID between the two devices.
  D. Correct the configuration of the vPC peer link and the vPC peer keepalive.
  E. Match the vPC domain ID between the two devices.

  ---

  Both "vPC peer link" and "Peer keepalive link" are down. So, D is correct.

  SW1 is using vPC domain ID 500, which SW2 is using 20. They must match. So, E is correct.

• Question 73:

  Refer to the exhibit.

  

  A Postman call to a Cisco APIC fails. The access credentials were confirmed to be configured as expected. Which action resolves the issue?

  A. Change operation type to POST
  B. Modify the protocol to HTTP
  C. Change the IP address to a domain name
  D. Modify the target protocol type to XML
  A. Change operation type to POST

  ---

• Question 74:

  Refer to the exhibit.

  

  To avoid service disruption, an engineer must move the_ server from LEAF_ 1 to LEAF_ _2. After running the test, the engineer noticed that L EAF_ 2 failed to forward network traffic into the VXL AN fabric. The BGP, interface NVE, and VNI were confirmed to be configured as expected. Which two actions must be taken on L EAF_ 2 to resolve the issue? (Choose two.)

  A. Change the fabric forwarding anycast-gateway-mac MAC address.
  B. Add fabric forwarding mode anycast-gateway on interface Vlan100.
  C. Configure correspondent IP addressing on every interface.
  D. Remove ip forward from interface VIan30 and add it on interface Vlan100.
  E. Enable HMM tracking to advertise host routes into the VXL AN fabric.
  A. Change the fabric forwarding anycast-gateway-mac MAC address.
  E. Enable HMM tracking to advertise host routes into the VXL AN fabric.

  ---

• Question 75:

  An engineer troubleshoots a packet flow from an access leaf to a spine. Which EVPN routes are expected on this connection?

  A. EVPN Type 1-5
  B. EVPN Type 0, 9, and 15
  C. EVPN Type 9-15
  D. EVPN Type 0 and 16
  A. EVPN Type 1-5

  ---

• Question 76:

  Refer to the exhibit.

  

  VSAN traffic is not routed as expected. Which action should be taken to resolve the issue?

  A. Reset the error packet counter
  B. Configure the hello timer to match the neighbor
  C. Configure the FSPF dead interval with a value higher than 80 seconds
  D. Reset the inactivity timer on switch-2
  B. Configure the hello timer to match the neighbor

  ---

  https://www.cisco.com/en/US/docs/switches/datacenter/nexus5500/sw/troubleshooting/guide/n5500_ts_sans.html

• Question 77:

  An engineer is troubleshooting a "Discovery Failed" error on a Cisco UCS C-Series server. The server is configured to be managed by the fabric interconnect directly. The engineer discovered that only the data connection is established with the fabric interconnect.

  Which port must be connected from the server to the fabric Interconnect to resolve the issue?

  A. MGMT port
  B. mLOM port
  C. PCIe port
  D. CIMC port
  D. CIMC port

  ---

• Question 78:

  Refer to the exhibit.

  

  A network engineer must use BGP to route IPv4 and IPv6 routes between R1 and R2. The IPv4 addresses are exchanged as expected between the routers through BGP. The routers have reached an Established BGP state. However, the IPv6 routes from R2 fail to show in the routing table of R1. Which action resolves the issue?

  A. Create a route map that sets the IPv6 next hop.
  B. Advertise L2VPN EVPN under IPv4 unicast address family
  C. Configure an IPv6 BGP neighbor on R1
  D. Enable IPv6 routing on R1
  A. Create a route map that sets the IPv6 next hop.

  ---

• Question 79:

  

  Refer to the exhibit. The user that was created on the RADIUS server does not have read-only access to the Cisco UCS Manager GUL. Also, the role for the user has not been configured inside Cisco UCS Manager. Which action must be taken inside Cisco UCS Manager to grant read-only access to the user?

  A. Change the provider group from Radius-Server to Local.
  B. Change the Console Authentication Realm to RADIUS.
  C. Change the Role Policy for Remote User to Assign Default Role.
  D. Change the Default Authentication Realm to read-only.
  C. Change the Role Policy for Remote User to Assign Default Role.

  ---

• Question 80:

  

  Refer to the exhibit. An engineer configures OSPF adjacency between two Cisco Nexus Series Switches called Nexus- 1 and Nexus-2. The OSPF adjacency fails to reach the FULL state. Which configuration on Nexus-1 resolves the issue?

  A. Set the MTU as 1492.
  B. Set the MTU as 9216.
  C. Modify the OSPF priority.
  D. Establish a OSPF point-to-point network.
  B. Set the MTU as 9216.

  ---