Cisco 300-615 Online Practice Questions and Exam Preparation

Cisco 300-615 Online Questions & Answers

• Question 191:

  You plan to use OSPFv2 on several Cisco Nexus 9000 Series Switches. Which setting must match on the neighboring switches to establish adjacency?

  A. the LSA arrival time
  B. the dead interval
  C. the last flood scan time
  D. the retransmit interval
  B. the dead interval

  ---

• Question 192:

  

  Refer to the exhibit. The receiver is listening to multicast group 239.200.0.1, but no packets are received for the requested multicast group. Which action resolves the issue?

  A. Configure both host MAC addresses as secure static on both interfaces.
  B. Change the port-security violation action to restrict on interface Eth1/2.
  C. Increase the maximum secure MAC addresses to 3 on interface Eth1/2.
  D. Modify the secure MAC address learning to sticky on both interfaces.
  A. Configure both host MAC addresses as secure static on both interfaces.

  ---

• Question 193:

  

  Refer to the exhibit. An engineer deploys a Cisco MDS 9000 Series Switch in a SAN. N9K-1 fails to learn the target WWNs and the interface fc1/4 fails to operate. The engineer collected this information about the environment:

  1.

  MDS-A is configured as an NPV switch.

  2.

  The WWNs of the storage array are present in the FLOGI database of MDS-A.

  3.

  Interfaces fc1/3 and fc1/4 on MDS-A and N9K-1 are enabled.

  Which set of actions resolves the issue?

  A. Set 0x000001 FCID on N9K-1 and reset interface fc1/4.
  B. On N9K-1, define fc1/4 as a trunk port and F port mode.
  C. Configure F port on MDS-A fc1/3 and N9K-1 fc1/4.
  D. Assign fc1/3 as NP port on MDS-A and F port on fc1/4 N9K-1.
  D. Assign fc1/3 as NP port on MDS-A and F port on fc1/4 N9K-1.

  ---

• Question 194:

  

  Refer to the exhibit. A Cisco VXLAN must use bidirectional PIM so that:

  1.

  Spine2 is the active RP for multicast group 225.0.0.0/24.

  2.

  Loopback 254 is used as a logical interface for PIM configuration.

  After configuration was applied, Spine1 became the active RP for multicast group 225.0.0.0/24 instead of Spine2. Which action resolves the issue?

  A. Delete the bidir keyword from ip pim rp address command on Spine1.
  B. Configure the IP pim ssm range 232.0.0.0/8 on Spine1.
  C. Modify the subnet mask of Loopback 254 to /30 on Spine2.
  D. Change the IP address of Loopback 254 to 10.254.254.254 on Spine2.
  D. Change the IP address of Loopback 254 to 10.254.254.254 on Spine2.

  ---

• Question 195:

  Refer to the exhibit.

  

  After an unexpected reload of the Cisco Nexus 9000 Series Switch, the network administrator noticed that one of the Software Maintenance Upgrades (SMU) images is inactive. The engineer must ensure that the package remains active after the switch is reloaded in the future. Which action accomplishes this goal?

  A. Copy the SMU package file on the bootflash
  B. Deactivate and uninstall the active core package
  C. Save the running configuration after activating the package
  D. Commit the package using the install commit command
  D. Commit the package using the install commit command

  ---

• Question 196:

  Refer to the exhibit.

  

  An engineer is troubleshooting the connectivity between Server-1 and Server-2. Which action resolves the connectivity issue?

  A. Enable BGP advertise pip feature on both leaf switches
  B. Configure the same source IP address on NVE and virtual peer link on leaf switches
  C. Classify CFS messages for strict priority queue on spine switches
  D. Change all ports on spine switches as port-type fabric
  A. Enable BGP advertise pip feature on both leaf switches

  ---

  https://www.cisco.com/c/en/us/td/docs/dcn/nx-os/nexus9000/101x/configuration/vxlan/cisco-nexus-9000-series-nx-os-vxlan-configuration-guide-release-101x/m_configuring_vpc_multihoming.pdf

• Question 197:

  

  Refer to the exhibit. Server A and Server B experience inter-L2VN reachability issues. A BGP L2VPN session is up on both leaf switches and each leaf switch learns the host routes of its local server, but the remote host routes are not in the VRF routing table. Which configuration resolves the issue?

  A. Associate Layer 3 VNI to VRF on the NVE interface for both leaf switches.
  B. Modify multicast groups on Leaf1 to be unique per VNI.
  C. Apply an anycast gateway to each SVI gateway on both leaf switches.
  D. Configure BGP VPNv4 neighborship between the leaf switches and the spine.
  A. Associate Layer 3 VNI to VRF on the NVE interface for both leaf switches.

  ---

• Question 198:

  

  Refer to the exhibit. An engineer is configuring zone distribution on the Cisco Nexus 9000 Series Switch. After initial configuration, the zone distribution for VSAN 20 from core-2 to edge-2 fails. Which action resolves the issue?

  A. Issue permit distribute on core-2.
  B. Set port mode to NP on edge-2.
  C. Change interop mode on core-2 to 1.
  D. Create VSAN 20 on ecge-2.
  D. Create VSAN 20 on ecge-2.

  ---

• Question 199:

  A network engineer is attempting to integrate Cisco UCS Manager with Cisco UCS Central, but the integration fails. The engineer can ping Cisco UCS Central from Cisco UCS Manager. Which two actions resolve the issue? (Choose two.)

  A. Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.
  B. Assign the Cisco UCS Central license to Cisco UCS Manager.
  C. Synchronize Cisco UCS Manager and Cisco UCS Central by using NTP.
  D. Place Cisco UCS Manager on the same subnet as Cisco UCS Central.
  E. Permit port 443 between Cisco UCS Manager and Cisco UCS Central.
  A. Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.
  C. Synchronize Cisco UCS Manager and Cisco UCS Central by using NTP.

  ---

• Question 200:

  DRAG DROP

  Drag each item listed on the left to its proper category on the right Not all items will fit the categories.

  Select and Place:

  

  

  ---

  Explanation/Reference: