Cisco 300-615 Online Practice Questions and Exam Preparation

Cisco 300-615 Online Questions & Answers

• Question 181:

  Refer to the exhibit.

  

  A network engineer finds one of the fabric interconnects offline when connecting L1 and L2 ports on both fabric interconnects. Which action resolves the issue?

  A. 1. Connect to Fabric Interconnect B. 2. Verify the cluster status and HA election. 3. Validate Fabric Interconnect B hardware issues.
  B. 1. Connect to Fabric Interconnect A. 2. Verify the cluster status and HA election. 3. Validate Fabric Interconnect A hardware issues.
  C. 1. Connect Fabric Interconnect B and change the role to primary. 2. Reboot Fabric Interconnect B. 3. Add the Fabric Interconnect A as subordinate fabric to the cluster.
  D. 1. Connect Fabric Interconnect B and execute "Erase configuration" 2. Reboot Fabric Interconnect B. 3. Add the subordinate Fabric Interconnect to the cluster.
  D. 1. Connect Fabric Interconnect B and execute "Erase configuration" 2. Reboot Fabric Interconnect B. 3. Add the subordinate Fabric Interconnect to the cluster.

  ---

• Question 182:

  A mission-critical server is connected to site A. Connectivity to this server is lost from site B because the MAC route is missing in the OTV VDC of the Nexus 7000 in site B due to MAC aging. Which action allows the flooding of the unknown unicast MAC on the Nexus 7000 in the OTV VDC?

  A. Use route-map to advertise this MAC statically and redistribute with ISIS.
  B. Unknown unicast flooding is not allowed.
  C. Use the otv flood mac command to selectively flood traffic for a given MAC.
  D. Use the otv isis bfd command to configure BFD protocol.
  B. Unknown unicast flooding is not allowed.

  ---

• Question 183:

  Refer to the exhibit.

  

  A network administrator created an EEM script to alert network management about flapping interfaces on a Cisco Nexus Series Switch. The applet must run when an interface flaps three times within 10 minutes. The EEM script fails to run as expected. Which action resolves the issue?

  A. Use integer data within the SNMP trap.
  B. Change the event period to 600.
  C. Configure a policy-default action.
  D. Associate a scheduler to the EEM script.
  B. Change the event period to 600.

  ---

• Question 184:

  Which action do you take to recover a Cisco UCS Director password?

  A. Use SSH to log in to the device, and then reset the password.
  B. Mount the Cisco UCS Director image on a KVM, reload the device, and then reset the password.
  C. Log into the Cisco UCS Director appliance as root, and then run the admin password reset script.
  D. Press CTRL-Break when the system boots, and then configure the config-register command to ignore the current configuration.
  C. Log into the Cisco UCS Director appliance as root, and then run the admin password reset script.

  ---

• Question 185:

  

  

  Refer to the exhibit. Which action must be taken to change the interface Eth1/3 on N9K-3 from suspended to up in the port channel?

  A. Change channel-group 9 mode from active to passive on N9K-3.
  B. Add vPC number under interface port-channel 2 for N9K-1 and N9K-2.
  C. Add peer-keepalive source and destination under vPC domain 100 for N9K-1 and N9K-2.
  D. Change channel-group ID from 9 to 2 on N9K-3.
  D. Change channel-group ID from 9 to 2 on N9K-3.

  ---

• Question 186:

  

  Refer to the exhibit. An engineer applied a VXLAN tunnel between Cisco Nexus 5000 Series Switches to extend the Layer 2 segment between N7K-1 and N7K-2. However, there is still no reachability between N7K-1 and N7K-2 over VLAN 200.

  Which configuration on N5K-2 resolves the issue?

  A. bridge-domain 200 member vni 9000
  B. interface vlan 200 vrf member vxlan-9000
  C. interface nve 1 member vni 9000 mcast-group 224.1.1.1
  D. vlan 200 vn-segment 9000
  D. vlan 200 vn-segment 9000

  ---

• Question 187:

  Refer to the exhibit.

  

  After the configuration is performed, the Guest shell continues to use 2% CPU. Which action resolves the issue?

  A. Resync the database
  B. Recreate the guestshell
  C. Reboot the guestshell
  D. Reboot the switch
  C. Reboot the guestshell

  ---

• Question 188:

  Refer to the exhibit.

  

  A network administrator must delete a feature group from a Cisco Nexus 5000 Series Switch. Which action resolves the issue?

  A. Detach the association with the no rule command within the role configuration mode
  B. Detach the association with the no role command within the feature-group configuration mode
  C. Detach the association with the no rule command within the feature-group configuration
  D. Detach the association with the no role command within the role configuration mode
  A. Detach the association with the no rule command within the role configuration mode

  ---

• Question 189:

  

  Refer to the exhibit. An engineer must restore the connectivity issue between NEXUS-SW-3 and NEXUS-SW-4. The engineer can ping the physical and loopback interfaces used in the underlay from VTEP-1. However, communication between the SVIs in NEXUS-SW-3 and NEXUS-SW-4 fails. Which action resolves the issue?

  A. Change the VNI to VLAN mapping on the NEXUS-SW-2.
  B. Reload the NEXUS-SW-2 to enable the hardware Ethernet store-and-fwd-switching feature.
  C. Manually set the interface MTU to support jumbo frames on the NEXUS-SW-2.
  D. Reconfigure the VXLAN features in the VTEP switches on the NEXUS-SW-2.
  A. Change the VNI to VLAN mapping on the NEXUS-SW-2.

  ---

• Question 190:

  You are configuring a Cisco Nexus 9000 Series Switch. Which configuration can be implemented for VXLAN BGP EVPN?

  A. VXLAN BGP EVPN by using an NVE interface in a default VRF
  B. RACLs on the Layer 3 uplinks for the VXLAN traffic
  C. QoS classification for the VXLAN traffic on all of the interfaces
  D. DHCP snooping on the VXLAN VLANs
  A. VXLAN BGP EVPN by using an NVE interface in a default VRF

  ---