Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 361:

  Refer to the exhibit.

  

  You must configure a port channel from each host. Which command do you run on the system-uplink port profile of the VSM?

  A. channel-group auto mode active
  B. channel-group auto mode on
  C. channel-group auto mode on mac-pinning
  D. channel-group auto mode passive
  C. channel-group auto mode on mac-pinning

• Question 362:

  You upgrade an operating system on a Cisco UCS C-Series Rack Server. After the upgrade, you discover that the performance of the server is much slower than expected. You verify that the operating system is on the Cisco support matrix for the rack server. Which two firmware types are the possible cause of the performance issue? (Choose two.)

  A. fNIC
  B. eNIC
  C. mptspi
  D. vNIC
  E. vSwitch
  A. fNIC
  B. eNIC

• Question 363:

  In order to fulfill the requirement to prevent the creation of end-to-end loops across a multihomed OTV network that connects two different data centers, what is the solution to this problem?

  A. prioritize the transmission of STP BPDUs across the overlay
  B. design the DCI connectivity as a hub and spoke
  C. define a conservative TTL for all packets traversing the OTV network
  D. enable AED on a per-VLAN basis between each OTV edge device with the same site ID
  D. enable AED on a per-VLAN basis between each OTV edge device with the same site ID

• Question 364:

  A server administrator creates a new vNIC template to use when creating service profiles. The administrator uses this template as part of a service profile template to create eight service profiles. Then the administrator adds an additional VLAN, but the service profiles do not reflect this change.

  What happened?

  A. The server created the VLAN on the wrong fabric
  B. The server administrator used an updating service profile template.
  C. The server administrator used an initial vNIC template.
  D. The domain has disjoint L2 and cannot find an uplink to pin the new VLAN.
  A. The server created the VLAN on the wrong fabric

• Question 365:

  Which two options are Cisco UCS default user roles? (Choose two.)

  A. Administrator
  B. Server Equipment Administrator
  C. FCoE Administrator
  D. Server Resource Administrator
  E. LAN Administrator
  A. Administrator
  B. Server Equipment Administrator

• Question 366:

  Which method does Cisco recommend for recovering a fabric interconnect when you have no working images on the bootflash?

  A. Reboot the primary fabric interconnect.
  B. Receive the kickstart image by using TFTP.
  C. Download the system image.
  D. Initiate auto-install.
  B. Receive the kickstart image by using TFTP.

• Question 367:

  Refer to the exhibit. An administrator sees this message in the log while merging switch fabrics. What is the issue?

  

  A. Two switches have different zone names with the same members.
  B. Two switches have different zone set names with the same members.
  C. Two switches have the same zone set and zone name, but with different members.
  D. Two switches have the same zone set and zone name with the same members.
  C. Two switches have the same zone set and zone name, but with different members.

• Question 368:

  After removing a VMM domain from an EPG, you discover that the associated virtual port groups remain in the VMware vCenter configuration. What causes the virtual port groups to persist in the configuration?

  A. The MAC addresses that are learned by the ports of the spine switches are incorrect.
  B. The port groups are being used by a virtual machine network adapter.
  C. The MAC addresses that are learned by the ports of the leaf switches are incorrect
  D. There is a mismatch between the data center name in vCenter and the VMM controller policy.
  B. The port groups are being used by a virtual machine network adapter.

• Question 369:

  A customer is trying to boot an operating system installed on a Cisco UCS B-Series blade server after a RAID1 cluster migration. The RAID LUN remains in inactive state during and after the service profile association and the server does not boot. What is the cause of this problem?

  A. RAID1 is not supported in cluster migration mode on a Cisco UCS B-Series blade server.
  B. The local disk configuration policy in the service profile on the server is configured with Any Configuration mode rather than RAID1.
  C. The server needs to be booted via SAN in cluster migration to support RAID1.
  D. The Cisco UCS B-Series blade server has older firmware that needs to be updated first.
  B. The local disk configuration policy in the service profile on the server is configured with Any Configuration mode rather than RAID1.

• Question 370:

  At any given time, each server can be associated with how many service profiles?

  A. 1
  B. 2
  C. 5
  D. 10
  E. unlimited
  A. 1