Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 271:

  If a server is not associated with a service profile, the activated firmware remains pending. Which two steps should you take? (Choose two.)

  A. Manually reboot the server.
  B. Reset the server to a new profile.
  C. Reset the unassociated server to activate the firmware.
  D. Reinitialize the firmware process with Cisco UCS Manager.
  E. Download the firmware and start over.
  F. Shut down gracefully and start over.
  A. Manually reboot the server.
  C. Reset the unassociated server to activate the firmware.

• Question 272:

  Refer to the exhibit.

  

  The customer informs you of a problem they are encountering. What is the cause of the problem?

  A. The core upstream switch does not have NPIV enabled.
  B. The downstream switch does not have NPIV enabled.
  C. NPIV has been disabled on all switches.
  D. NPIV has been configured but not enabled on the uplink port.
  A. The core upstream switch does not have NPIV enabled.

• Question 273:

  A customer deploys a new Cisco UCS environment and is deploying new ESXi hosts. The customer fails to establish network connectivity to the KVM console. Which option is the most likely cause of the problem?

  A. wrong UUID
  B. missing user rights
  C. IP addressing overlap
  D. NIC pinning
  C. IP addressing overlap

• Question 274:

  Refer to the exhibit.

  

  You see the fault when configuring a global ID pool in Cisco UCS Central. Which issue could cause the fault?

  A. The same ID is defined in Cisco UCS Central and Cisco UCS Manager.
  B. The interval between the creation and the deletion of a service profile is less than 10 milliseconds.
  C. The blocks in the pools do not have an assigned ID range qualifier.
  D. The same ID is assigned to the service profiles in two registered domains.
  A. The same ID is defined in Cisco UCS Central and Cisco UCS Manager.

• Question 275:

  Which two options are causes for failure of a Cisco C-Series server that is configured to boot from SAN? (Choose two.)

  A. The boot LUN ID is not 0.
  B. The ISCSI target is only available via one via one path through the network.
  C. C-Series does not support boot from SAN.
  D. The KVM dongle is attached to the front of the server with a USB stick installed.
  E. Under the FCoE properties on the vNIC adapter, the FCoE VLAN ID is set to 10.
  F. The boot table for fc0 has not been configured.
  D. The KVM dongle is attached to the front of the server with a USB stick installed.
  F. The boot table for fc0 has not been configured.

• Question 276:

  Which command displays the traffic statistics for a port channel interface?

  A. show interface port-channel channel-number
  B. show port-channel traffic
  C. show port-channel usage
  D. show port-channel compatibility-parameters
  B. show port-channel traffic

• Question 277:

  While updating firmware in a Cisco UCS environment, what will the Cisco UCS Manager do?

  A. show you all versions available on Cisco.com
  B. show you all versions downloaded to the Cisco UCS Manager
  C. show you only versions that are supported in your environment
  D. show you only versions that you selected to show
  E. show you old and new versions from your download
  C. show you only versions that are supported in your environment

• Question 278:

  Which CLI command should you use to promote the local fabric interconnect to primary?

  A. cluster primary force
  B. cluster failover primary
  C. cluster force primary
  D. cluster failover
  E. failover
  C. cluster force primary

• Question 279:

  Which command would you use to find the AED of an extended VLAN in a dual-homed site of an OTV network?

  A. show otv aed on the AED
  B. show otv site on any edge devices in the site
  C. show otv vlan on the AED
  D. show otv aed on any edge devices in the site
  E. show otv vlan on any edge devices in the site
  C. show otv vlan on the AED

• Question 280:

  You must troubleshoot an issue with DAI on a Cisco Nexus switch. Drag and drop the DAI configuration steps from the left into the order they must be implemented in on the right.

  Select and Place: