Cisco 300-180 Online Practice Questions and Exam Preparation

Cisco 300-180 Online Questions & Answers

• Question 151:

  Which statement is true with respect to resetting a forgotten Cisco IMC admin password on a Cisco UCS C-Series rack-mount server?

  A. Download the Cisco IMC password reset utility ISO file from Cisco.com and boot from virtual media. The server will boot the Linux Live CD and reset the password to 'password'.
  B. Download the Cisco IMC password reset EFI plugin file from Cisco.com to a USB flash drive and boot to the EFI shell. The startup.nsh file will auto-load and reset the password to 'password'.
  C. Shut down the server and remove all power supplies for 3 minutes to allow the password capacitor to discharge. Use the default password 'password' to log back in.
  D. Shut down the server and remove all power cords. Open the case and short the jumper specified in the model-specific Cisco UCS C-Series Server Installation and Service Guide.
  D. Shut down the server and remove all power cords. Open the case and short the jumper specified in the model-specific Cisco UCS C-Series Server Installation and Service Guide.

• Question 152:

  

  

  

  While the Nexus 7010 switches are configured with vPC, the Nexus 5000 switch connections to each Nexus 7010 are configured as regular port-channels. Which statement best describes the problem affecting the port channel on N5K1?

  A. LACP is not configured to initiate negotiations.
  B. N5K1 must also be configured with vPC.
  C. load-balancing is not configured correctly on N5K1.
  D. The remote ends of the port-channel on N5K1 cannot use the same interface.
  D. The remote ends of the port-channel on N5K1 cannot use the same interface.

• Question 153:

  Refer to the exhibit.

  

  You configure a vPC between two Cisco Nexus 7000 Series switches but the peer link will not come up. What is the problem?

  A. The system priority must be the same.
  B. The configuration is correct. The problem lies elsewhere.
  C. The role priority must be the same.
  D. The vPC domain numbers must be different.
  B. The configuration is correct. The problem lies elsewhere.

• Question 154:

  Which three statements are true regarding trunking on an ISL between two switches in order for the VSAN to be trunked? (Choose three.)

  A. The VSAN must be defined on both switches.
  B. The VSAN must be on the VSAN allowed list.
  C. All VSANs that are being trunked must be using either enhanced or non-enhanced mode zoning, but not both.
  D. IVR must be configured for Cisco Fabric Services.
  E. The device alias database must successfully merge.
  F. There cannot be any duplicate domain IDs within an individual VSAN.
  A. The VSAN must be defined on both switches.
  B. The VSAN must be on the VSAN allowed list.
  F. There cannot be any duplicate domain IDs within an individual VSAN.

• Question 155:

  What is the default MTU size of a VMware host?

  A. 1000
  B. 1500
  C. 1550
  D. 9000
  B. 1500

• Question 156:

  What are the minimum number and maximum number of members that a SAN PortChannel can have?

  A. 1, 16
  B. 2, 16
  C. 1, 32
  D. 2, 32
  E. 1 minimum with no maximum
  F. 2 minimum with no maximum
  A. 1, 16

• Question 157:

  During the installation of Windows 2008 64-bit operating system on a Cisco UCS server, the RAID controller is not found. What is the cause of the problem?

  A. The Cisco IMC firmware needs to be updated.
  B. The LSI option ROM needs to be configured by pressing Ctrl-H during post.
  C. The LSI drivers are not bundled and need to be loaded by clicking the Load Driver option to point to the correct drivers.
  D. Windows 2008 64-bit operating system is not supported on Cisco UCS servers.
  C. The LSI drivers are not bundled and need to be loaded by clicking the Load Driver option to point to the correct drivers.

• Question 158:

  Which communication is exchanged between neighbors during OTV adjacency formation across the Layer 3 multicast network?

  A. IGMP packets
  B. OTV open messages
  C. L1 IS-IS Hello packets
  D. OTV adjacency packets
  C. L1 IS-IS Hello packets

• Question 159:

  Refer to the exhibit.

  

  An administrator is deploying FCoE; however, a VFC interface will not come up. The administrator executes the commandshow platform software fcoe_mgr info interface vfc and displays the output. What is the problem?

  A. An incorrect VSAN number is being used.
  B. The connected host does not support FIP.
  C. FCoE is not enabled.
  D. Priority flow control is not being negotiated with the converged network adapter.
  B. The connected host does not support FIP.

• Question 160:

  A customer has Server1 working properly, configured to boot over SAN and with service profile SP1 assigned. This service profile is cloned to service profile SP2 and assigned to Server2. Before Server2 boots, which three actions needs to be performed? (Choose three.)

  A. Check the WWPN that is assigned to the vHBAs on SP2.
  B. Check the MAC address that is assigned to the vNICs on SP2.
  C. Add two vHBAs and assign them to the proper VSAN.
  D. Add the pWWN of SP2 to the zoning on the SAN switch.
  E. Change the boot target on SP2.
  F. Change the IP address of the vNICs.
  A. Check the WWPN that is assigned to the vHBAs on SP2.
  D. Add the pWWN of SP2 to the zoning on the SAN switch.
  E. Change the boot target on SP2.