NetApp NS0-182 Online Practice Questions and Exam Preparation

NetApp NS0-182 Online Questions & Answers

• Question 81:

  While preparing for a new ONTAP installation, you discover an issue with the controllers that are running ONTAP 9.5. The issue is not affecting controllers that are running ONTAP 9.4 with the latest patch version. In this scenario, which two steps should you perform to solve the problem? (Choose two.)

  A. Review the issue with the customer's deployment to see if it would be affected.
  B. Inform your customer that they must always install the latest supported ONTAP release.
  C. If the controllers are in a Product Support Bulletin with ONTAP 9.5, open a case and wait for support to provide a patch release.
  D. Download ONTAP 9.4 with the latest patch version and ONTAP 9.5 for an eventual rollback on the day of the installation.
  C. If the controllers are in a Product Support Bulletin with ONTAP 9.5, open a case and wait for support to provide a patch release.
  D. Download ONTAP 9.4 with the latest patch version and ONTAP 9.5 for an eventual rollback on the day of the installation.

• Question 82:

  You are configuring a new system with ONTAP 9.5. You created interface groups, VLANs, and a broadcast domain for the new ports on all the nodes of your cluster. During the configuration, you used an MTU value of 1500 for the broadcast domain and 9000 for the physical ports. The customer asks you to enable jumbo frames.

  What should you do in this scenario?

  A. Set the MTU option to jumbo frames on the broadcast domain.
  B. Change the MTU value to 9000 on the ifgroup.
  C. Set the MTU option to jumbo frames on the ifgroup.
  D. Change the MTU value to 9000 on the broadcast domain.
  D. Change the MTU value to 9000 on the broadcast domain.

• Question 83:

  While preparing for a new cluster installation, your customer indicates that they have some disk shelves and switches that were discontinued at their old site. They want to re-use as much of this equipment as possible. You must verify that their discontinued equipment is compatible with the new equipment they have on order.

  Which two actions will accomplish this task? (Choose two.)

  A. Use the Hardware Universe portal (HWU).
  B. look up the compatibility in the Interoperability Matrix Tool (IMT).
  C. Verify compatibility from Activity IQ.
  D. Run the Cluster Configuration Builder tool (ConfigBuilder).
  B. look up the compatibility in the Interoperability Matrix Tool (IMT).

• Question 84:

  You just finish the installation of a single-node cluster. You want to make sure that the cluster backups are saved to a different location. What is required to accomplish this task?

  A. Set up AutoSupport
  B. Enable copy offloading.
  C. Set up SVM disaster recovery.
  D. Configure a system configuration backup.
  D. Configure a system configuration backup.

• Question 85:

  Without adding new cluster interconnect switches, you want to nondisruptively upgrade from FAS2554 controllers to FAS8200 controllers on an existing 2-node switchless cluster running ONTAP 9.5 software. Which statement is correct in this scenario?

  A. Relocate the aggregates to one FAS2554 node, takeover, replace the node in takeover state with a FAS8200 node, reassign the disks, giveback, and repeat for the second node.
  B. Connect the FAS8200 to the FAS2554 with interconnect cables, join the existing cluster, relocate the aggregates from the FAS2554 to the FAS8200, and decommission the FAS2554.
  C. Set up the FAS8200 as a new cluster, move the SVMs from the FAS2554 to the FAS8200 using SVM move, and decommission the FAS2554.
  D. You cannot perform this task nondisruptively.
  A. Relocate the aggregates to one FAS2554 node, takeover, replace the node in takeover state with a FAS8200 node, reassign the disks, giveback, and repeat for the second node.

• Question 86:

  You are going to add a node to an existing cluster but first you must gather the appropriate information for the new node's management LIF. What two pieces of information is required to accomplish this task? (Choose two.)

  A. IP address
  B. NTP server address
  C. Service Processor Information
  D. default gateway
  A. IP address
  D. default gateway

• Question 87:

  Your customer wants to buy four new DS212C shelves with an 8 TB SATA drive. The customer also wants to know the usable aggregate size of this configuration. In this scenario, which resource would you use to accomplish this task?

  A. Fusion
  B. Hardware Universe (HWU)
  C. Interoperability Matrix Tool (IMT)
  D. Config Advisor
  B. Hardware Universe (HWU)

• Question 88:

  You are asked to install a 2-node FAS2554 cluster running ONTAP 9.5. The controller arrived with ONTAP 9.0 installed. In this scenario, which two tools would be used to complete this upgrade for this installation? (Choose two.)

  A. HTTP server
  B. SMTP server
  C. FTP server
  D. SNMP server
  A. HTTP server
  C. FTP server

• Question 89:

  A customer wants to reduce the task allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part. The small part is used for the root aggregate and the large part for the data aggregates?

  In this situation, what is this feature called?

  A. ONTAP
  B. RAID
  C. storage virtual machine
  D. Advanced Drive Partitioning
  D. Advanced Drive Partitioning

• Question 90:

  Referring to the exhibit(Missing the exhibit), which statement describes the duster network used by the cluster interconnect ports?

  A. The network that allows all nodes in the cluster to have direct access to every other node's disk shelves.
  B. The network used to allow all nodes to communicate with the users for data access.
  C. The network used to allow all nodes to communicate with the customer (or management access.
  D. The network used to allow all nodes to communicate for internal (private) data access.
  D. The network used to allow all nodes to communicate for internal (private) data access.