NetApp NS0-182 Online Practice Questions and Exam Preparation

NetApp NS0-182 Online Questions & Answers

• Question 1:

  You install a new 2-node FAS8200 switchless cluster. You want to reach all necessary management LIFs and SPs for this cluster. How many management IP addresses do you need in this scenario?

  A. 1
  B. 2
  C. 5
  D. 4
  C. 5

• Question 2:

  Which two commands verify that AutoSupport is working as expected?

  A. autosupport test show
  B. autosupport history show
  C. autosupport check show
  D. autosupport show
  B. autosupport history show

• Question 3:

  While troubleshooting an issue with a newly installed system, you used the system controller environment show command. In this scenario, which issue would be diagnosed with this command?

  A. shelf cabling issues
  B. controller configuration issues
  C. controller hardware issues
  D. controller version issues
  C. controller hardware issues

• Question 4:

  What are two types of load balancing methods available in multimode interface groups? (Choose two.)

  A. broadcast domain-based load balancing
  B. IP-based load balancing
  C. LIF-based load balancing
  D. port-based load balancing
  B. IP-based load balancing
  D. port-based load balancing

• Question 5:

  You are asked to installed a new cluster with six FAS8060 nodes. While running Config Advisor, you determine that there is a newer firmware version for 16 HDDs. How should this situation be handled?

  A. Prior to leaving the site, advise the customer that firmware is included with the version of ONTAP they selected.
  B. Unless the customer advises otherwise, upgrade the firmware on the HDDs to correct the Config Advisor error.
  C. Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.
  D. Prior to leaving the site, confirm the version of ONTAP that the customer wanted installed to correct the Config Advisor error.
  B. Unless the customer advises otherwise, upgrade the firmware on the HDDs to correct the Config Advisor error.

• Question 6:

  Select the Exhibit tab.

  

  Your customer has an AFF A300 installed. They ask you to configure the e0a and e0b ports to use the FC protocol. Referring to the exhibit, which statement is correct in this scenario?

  A. These ports are used for the Ethernet uplink into the customer's network.
  B. The configuration of these ports can only be done by OnCommand System Manager.
  C. These ports are used for the cluster interconnect.
  D. Use the ucadmin command to configure these ports as FC ports.
  C. These ports are used for the cluster interconnect.

• Question 7:

  A customer has an AFF A800 with 24 internal drives and is running out of storage capacity. In this scenario, which action will solve this issue?

  A. Insert more internal NVMe SSD drives.
  B. Attach an additional DS212C shelf, filled with drives.
  C. Attach an additional DS460C shelf, filled with drives.
  D. Insert more internal SSD drives.
  A. Insert more internal NVMe SSD drives.

• Question 8:

  You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on. Which two actions should you perform before you turn over the cluster for production? (Choose two.)

  A. Remove cables connected to the controller until you find the one responsible for the controller issue.
  B. Review AutoSupport messages which could explain the controller state.
  C. Execute Config Advisor again to check for new errors.
  D. Let the customer know the cluster is operating normally while the amber LED is on.
  A. Remove cables connected to the controller until you find the one responsible for the controller issue.
  C. Execute Config Advisor again to check for new errors.

• Question 9:

  During handover, a customer asks you how to obtain support from NetApp after installation. What are two responses in this scenario? (Choose two.)

  A. Visit.
  B. Visit mysupport.netapp.com
  C. Send an AutoSupport message from the system.
  D. Contact Global Support by telephone.
  B. Visit mysupport.netapp.com
  C. Send an AutoSupport message from the system.

• Question 10:

  A customer wants to expand a 10-node AFF A700s NAS cluster running with Cisco Nexus 3132Q-V cluster interconnect switches using new nodes. In this scenario, what is the maximum number of nodes to be added into this cluster?

  A. 24
  B. 2
  C. 12
  D. 14
  B. 2