NetApp NS0-182 Online Practice Questions and Exam Preparation

NetApp NS0-182 Online Questions & Answers

• Question 161:

  A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports. However, LIFs that serve the block have not migrated.

  In this scenario, what is happening?

  A. The failover group is configured incorrectly.
  B. The fiber switch is configured incorrectly.
  C. There is a faulty SFP.
  D. The LIFs that serve the block protocol do not failover.
  B. The fiber switch is configured incorrectly.

• Question 162:

  A customer wants you to add a new AFF A700 HA pair to an existing 4-node AFF8080 EX cluster. The existing cluster uses NetApp CN1610 switches for the cluster connection and is using the recommended port count. Which statement is true in this scenario?

  A. You cannot have more than four nodes with AFF.
  B. There are not enough ports available on the cluster switch.
  C. The AFF A700 is not supported with NetApp CN1610 switches/
  D. You cannot mix different AFF models in the same cluster.
  D. You cannot mix different AFF models in the same cluster.

• Question 163:

  At a new Installation, you run Config Advisor and see the warnings shown In the exhibit. What should you do to correct the warnings on the node?

  A. Set the flow control on all the 10GbE ports to none, and delete the AutoSupport settings.
  B. Set the flow control on all of the l0GbE or 40GbE cluster interconnect ports to None.
  C. Delete all of the AutoSupport settings, and change the flow control to full.
  D. Set the flow control on all the lGbE ports to match the 10GbE pods.
  B. Set the flow control on all of the l0GbE or 40GbE cluster interconnect ports to None.

• Question 164:

  Your customer has filled out the customer installation worksheet. However, the customer's network environment is not set up and ready for the new ONTAP 9.5 system. The customer requests that you install the system and states that they will finish the configuration when they have acquired the appropriate network connections.

  Which two statements are correct about this scenario? (Choose two.)

  A. You should cable a cluster so that the clusters interconnect traffic is on a separate network from all other traffic.
  B. You cannot install an ONTAP system without having the customer network configuration.
  C. You should cable all of the controllers and disk shelves, power on the system, and then leave the system as-is for the customer to configure.
  D. A cluster can be created without data network connections, but it must include a cluster interconnect connection.
  A. You should cable a cluster so that the clusters interconnect traffic is on a separate network from all other traffic.
  D. A cluster can be created without data network connections, but it must include a cluster interconnect connection.

• Question 165:

  You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are associated with this port are migrated to a port that is not expected. In this scenario, what would cause this behavior?

  A. The network port is configured incorrectly.
  B. The broadcast domain is configured incorrectly.
  C. There are no online ports within the same failover group.
  D. The network failover port is not licensed.
  C. There are no online ports within the same failover group.

• Question 166:

  Which NetApp tool should you use to set up an ONTAP 9.5 cluster?

  A. Config Advisor
  B. System Setup
  C. SANtricity Storage Manager
  D. OnCommand System Manager
  A. Config Advisor

• Question 167:

  Select the Exhibit tab.

  

  Referring to the exhibit, a customer wants to migrate LIF lif1_iscsi to node cluster1-02 port e0d, but they receive an error. What is the cause of this error?

  A. The LIF is not properly configured.
  B. The designation port is not available.
  C. This type of LIF cannot be migrated.
  D. The LIF does not have a failover group.
  C. This type of LIF cannot be migrated.

• Question 168:

  Upon finishing the installation of a new system for a customer, they request that you train them on how to administer the system. In this scenario, which two responses are appropriate? (Choose two.)

  A. Visit the NetApp MySupport Site and look for the Express Guides, they will guide you through the daily tasks and provide input and output examples.
  B. If you have a specific issue, you can visit the Knowledge Base Web site (https://kb.netapp.com).
  C. The answers to any of your questions can be found on the NetApp SmartSolve site (http://smartsolve.netapp.com).
  D. You should open a case with NetApp Support for all future questions with low priority and include the keyword "Training" in the title.
  A. Visit the NetApp MySupport Site and look for the Express Guides, they will guide you through the daily tasks and provide input and output examples.
  C. The answers to any of your questions can be found on the NetApp SmartSolve site (http://smartsolve.netapp.com).