NetApp NS0-182 Online Practice Questions and Exam Preparation

NetApp NS0-182 Online Questions & Answers

• Question 151:

  After properly cabling the NetApp CN1610 cluster switches, you see that joining the second node to a cluster fails because the node is not able to communicate with the other node. In this scenario, what is causing this problem?

  A. The cluster switches must be Cisco for more than two nodes in a cluster.
  B. The RCF file is not loaded properly.
  C. CN1610 is unsupported in newer ONTAP versions.
  D. The NTP server is not set.
  B. The RCF file is not loaded properly.

• Question 152:

  You are preparing for an installation of a 2-node switches cluster ONTAP 9.5 prior to leaving for the customer's site, you verify that the correct items were ordered to complete the install. In this scenario, what should be verified?

  A. The Service Event Report
  B. The unified Parser output
  C. The sales order
  D. The Configure Advisor output
  C. The sales order

• Question 153:

  You have a 6-node ONTAP 9.1 cluster with two FAS6290 nodes and four FAS8080 EX nodes using a SAN protocol. In this scenario, how many FAS9000 HA pairs would be joined to this cluster?

  A. 3
  B. 2
  C. 9
  D. 6
  D. 6

• Question 154:

  What is the maximum port speed of an Ethernet port on a Cisco Nexus 3232C cluster-interconnect switch?

  A. 40GbE
  B. 200GbE
  C. 10GbE
  D. 100GbE
  A. 40GbE

• Question 155:

  You need to verify the configuration currently loaded on a Cisco Nexus 3132Q-V cluster switch after applying the RCF. Which command will accomplish this task?

  A. Use the show bootvar command.
  B. Use the verify config command.
  C. Use the show startup-conf command.
  D. Use the show running-config command
  D. Use the show running-config command

• Question 156:

  A customer ordered two new DS224C shelves. The customer wants you to add these shelves to an existing stack which consists of two DS2246 shelves. Which statement is true in this scenario?

  A. You need to order additional cables to expand the existing stack.
  B. Mixing DS224C and DS2246 shelves in the same node are not supported.
  C. You cannot mix DS224C and DS2246 shelves in the same stack.
  D. DS224C shelves are supports with only new HBAs.
  D. DS224C shelves are supports with only new HBAs.

• Question 157:

  You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.

  In this scenario, what caused this problem?

  A. Breakout cables were used and the second port on the same ASIC became disabled.
  B. This is a hardware error and you must open a case with NetApp Support.
  C. You must first enable the ports using the network port modify command.
  D. You are missing a license to enable those ports.
  C. You must first enable the ports using the network port modify command.

• Question 158:

  You want to expand an existing FAS8060 switchless cluster running ONTAP 9.5 with an AFF A300 system.

  Which action should you take to perform this task?

  A. Execute the cluster setup command on the existing FAS8060 cluster, add the cluster interconnect switches, and cable both the FAS8060 cluster and the AFF A300 system to the new cluster.
  B. Create a separate switchless cluster with the AFF A300 system.
  C. Connect the cluster ports of the AFF A300 system to the existing FAS8060 cluster, and join the existing cluster.
  D. Add and configure the cluster interconnect switches, re-cable the FAS8060 cluster, add the AFF A300 system, and join the existing cluster.
  C. Connect the cluster ports of the AFF A300 system to the existing FAS8060 cluster, and join the existing cluster.

• Question 159:

  You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs. Which statement is correct in this scenario?

  A. Prior to leaving the site, tell the customer that a later firmware exists for those disk drives, but that the upgrade will provoke downtime.
  B. Unless the customer advises otherwise, upgrade the firmware on the SSDs to clear the Config Advisor error.
  C. Prior to leaving the site, advise the customer that the firmware is included in the version of ONTAP that they downloaded.
  D. Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.
  C. Prior to leaving the site, advise the customer that the firmware is included in the version of ONTAP that they downloaded.

• Question 160:

  What is a node?

  A. A node refers to all physical devices bound together In the cluster.
  B. A node is the logical device that shares data.
  C. A node is a logical network port.
  D. A node is a controller that is part of the cluster.
  D. A node is a controller that is part of the cluster.