NetApp NS0-182 Online Practice Questions and Exam Preparation

NetApp NS0-182 Online Questions & Answers

• Question 101:

  You installed a new AFF A800 2-node ONTAP 9.5 cluster and are asked to run diagnostics to validate the hardware. Which command is used from the loader prompt to enter diagnostics?

  A. printenv
  B. savenv
  C. sldiag
  D. boot_diags
  D. boot_diags

• Question 102:

  Which statement describes an SVM?

  A. An SVM is a logical device that shares data.
  B. An SVM is a node in the cluster.
  C. An SVM is a logical network interface.
  D. An SVM is a storage volume type.
  D. An SVM is a storage volume type.

• Question 103:

  After an installation, your customer asks you if you have a solution or a product that can easily list all the elements of a running ONTAP cluster, and highlight the changed and new objects including IP addresses, subnets, IPspaces, SVMs, volumes, and LUNs. For easy modification the output should be a document or a spreadsheet. Your customer does not have any PowerShell or scripting knowledge.

  In this scenario, which Windows PowerShell-based NetApp tool would help to extract this information?

  A. NetApp Management SDK
  B. NetAppDocs
  C. NetApp PowerShell Toolkit
  D. NetApp Synergy
  C. NetApp PowerShell Toolkit

• Question 104:

  A customer has recently purchase a new ONTAP 9.0 storage system and wants you to join the nodes to an existing cluster running ONTAP 9.5. What is the first step for adding the new controllers to the existing cluster?

  A. You must ensure that all network switches are upgraded and online.
  B. You must configure the existing cluster to accept the Joining nodes.
  C. You must make sure that there Is the same amount of disk shelves attached to all nodes.
  D. You must match the operating system.
  D. You must match the operating system.

• Question 105:

  You have just added a new DS4246 shelf with 24 x 10 TB SATA HDDs to a single FAS2650 node as the first SATA shelf. You must keep two SATA spare disks on the shelf. What is the maximum number of SATA data disks available in this scenario?

  A. 19
  B. 16
  C. 22
  D. 20
  D. 20

• Question 106:

  Recently, your 2-node FAS8020 cluster was upgraded from ONTAP 8.3 to ONTAP 9.5. You have just added two FAS8060 nodes to the cluster. You have executed Config Advisor to verify your work. Config Advisor tells you that the cluster ports on the original two FAS8020 nodes have Flow Control set to FULL.

  In this scenario, to what should the Flow Control setting on the FAS8020 ports be set?

  A. Flow Control should be set to SEND.
  B. Flow Control should be set to ALL.
  C. Flow Control should be set to RECEIVE.
  D. Flow Control should be set to NONE.
  B. Flow Control should be set to ALL.

• Question 107:

  After you install a new cluster with ONTAP 9.5 software, you want to create a new broadcast domain. During the creation of the broadcast domain, you receive an error that there are no free ports available. What is the reason for this error message?

  A. By Default, all ports are bound to the "Default" broadcast domain. To create a new port, remove the needed ports from the "Default" broadcast domain and create a new IPspace.
  B. By Default, all ports are bound to the "Default" broadcast domain. To create a new port, remove the needed ports from the "Default" broadcast domain.
  C. Before you configure a new broadcast domain, you should create a new IPspace.
  D. You can create a new broadcast domain only within the CLI.
  C. Before you configure a new broadcast domain, you should create a new IPspace.

• Question 108:

  You create a LIF called svm_cifs_lif01 on a port that is already in an up state. After you test the storage failover, the LIF does not automatically revert to its home port. In this scenario, what should you do to solve the problem?

  A. Configure a new failover group.
  B. Configure the LIF with the DHCP option.
  C. Add the port in a broadcast domain.
  D. Configure the LIF with the automatic revert option.
  D. Configure the LIF with the automatic revert option.

• Question 109:

  Your customer regularly schedules disaster recovery tests to ensure the high availability capabilities of the ONTAP cluster. In this scenario, which two commands would you use to perform this test? (Choose two.)

  A. system node run -node NetApp-Cluster-02 -command cf takeover
  B. storage failover giveback -of-node NetApp-Cluster-02
  C. system node run -node NetApp-Cluster-02 -command cf giveback
  D. storage failover takeover -of-node NetApp-Cluster-02
  B. storage failover giveback -of-node NetApp-Cluster-02
  D. storage failover takeover -of-node NetApp-Cluster-02

• Question 110:

  You have just installed a new FAS2650 HA for your customer. You are now configuring the NetApp AutoSupport transport section. In this scenario, what is the NetApp best practice for this task to allow AutoSupport on Demand (ASOD)?

  A. Use SMTP.
  B. Use HTTPS.
  C. Use HTTP.
  D. Use SSH.
  B. Use HTTPS.