NetApp NCSIE ONTAP NS0-182 Questions & Answers

• Question 41:

  You complete a hardware installation on a CN1610 switch and establish a serial connection to the RJ45 port.

  In this scenario, the established serial connection allows the installer to complete which two tasks for the switches initial configuration? (Choose two.)

  A. to view network information that has been dynamically assigned to the management interface by the DHCP server on the network

  B. to use the serial port connection as a diagnostic channel to the second CN1610 switch in the cluster interconnect

  C. to configure the switch with another CN1610 switch using Cross-Stack EtherChannel configuration for load balancing and performance

  D. to manually configure the static network information

  Correct Answer: AD

  Reference: https://library.netapp.com/ecm/ecm_download_file/ECMP1117853 (34)

• Question 42:

  When planning the installation of a new ONTAP 9.5 cluster for a customer, which three steps should you perform? (Choose three.)

  A. Complete a Service Event Report.

  B. Use Config Builder to create a configuration spreadsheet.

  C. Review the hardware components in Hardware Universe.

  D. Open a support case to prepare for the installation.

  E. Search for Technical Support bulletins for the hardware.

  Correct Answer: ABC

• Question 43:

  After properly cabling the NetApp CN1610 cluster switches, you see that joining the second node to a cluster fails because the node is not able to communicate with the other node.

  In this scenario, what is causing this problem?

  A. The cluster switches must be Cisco for more than two nodes in a cluster.

  B. The RCF file is not loaded properly.

  C. CN1610 is unsupported in newer ONTAP versions.

  D. The NTP server is not set.

  Correct Answer: B

• Question 44:

  A customer has a 6-node AFF A700 cluster and wants to add four nodes without having to update license functionality for each node manually.

  In this scenario, which type of license provides this functionality?

  A. Demo License

  B. Site License

  C. Standard License

  D. Evaluation License

  Correct Answer: C

• Question 45:

  You have just installed a new AFF A220 4-node cluster with ONTAP 9.5 for a customer. Which two cluster switches are supported in this scenario? (Choose two.)

  A. Cisco Nexus 5596UP

  B. Brocade 6510

  C. Cisco MDS 91485

  D. NetApp CN1610

  Correct Answer: AD

• Question 46:

  A customer buys a new switchless ONTAP 9.5 FAS2650 cluster. You are asked to install the system at the customer's site.

  Which three steps are needed to accomplish this task? (Choose three.)

  A. Cable the ACP.

  B. Cable the cluster-interconnect to the CN1610 switches.

  C. Connect both power cords.

  D. Install the system in the rack.

  E. Cable the controller for switchless ONTAP software.

  Correct Answer: CDE

• Question 47:

  

  You want to create a new intercluster LIF for cross-cluster replication and use the CLI. After you create the nac101_intercluster_lif_icl LIF, you are not able to see the LIF in the list of local intercluster LIFs. Referring to the exhibit, what is the problem?

  A. The assigned port for the intercluster e1c LIF is in the down admin state.

  B. The intercluster LIF has assigned an IP address that is not in the intercluster VLAN.

  C. The LIF that was created has the wrong role type.

  D. The home node of the new intercluster LIF has reached the maximum of four intercluster LIFs.

  Correct Answer: B

• Question 48:

  What is a valid failover policy for a SAN LIF?

  A. disabled

  B. broadcast-domain-wide

  C. system-define

  D. local-only

  Correct Answer: B

• Question 49:

  When completing a new ONTAP 9.5 cluster base installation, which three SVM types will be present on the system by default? (Choose three.)

  A. admin SVM

  B. system SVM

  C. cluster SVM

  D. data SVM

  E. node SVM

  Correct Answer: ABE

  Reference: https://thinksystem.lenovofiles.com/help/topic/system_administration_guide/M_B5B94D5E9735-4C9B-8754-73A9599D8D74_.pdf

• Question 50:

  Click the Exhibit button.

  

  After you install a FAS2720 with ONTAP 9.5, you disconnect the management port of node A to demonstrate cluster management LIF failover to the custom. When you reconnect the management port and try to revert the interface, you receive the following message.

  Info: LIF "cluster_mgmt" has been hosted on port "NetApp-Cluster-01:e0M", whose health status is degraded.

  You issue the network port show command and see the output shown in the exhibit. When you try to access the cluster interface, you cannot ping or connect to the cluster through the network.

  Which two troubleshooting steps must you perform to solve the issue? (Choose two.)

  A. Set the Ignore Health Status parameter to true.

  B. Use the network port modify -up-admin command to administratively down and up the port.

  C. Reconnect the management cable to bring the port online.

  D. Set the Ignore Health Status parameter to false.

  Correct Answer: BC