NetApp NCSIE ONTAP NS0-182 Questions & Answers

• Question 31:

  After the installation of a new 2-node cluster, you want to make sure that AutoSupport is working as expected from the cluster.

  In this scenario, what are two ways to trigger a new Auto Support? (Choose two.)

  A. Use the ping command on the mailhost.

  B. Use the OnCommand UnifiedManager GUI.

  C. Use the OnCommand System Manager GUI.

  D. Use the system node autosupport invoke -type test command.

  Correct Answer: CD

• Question 32:

  A customer has a stack of shelves with both DS4243 shelves and DS4246 shelves. The customer wants to replace the DS4243 shelves with new DS4246 shelves.

  What would you advise the customer in this scenario?

  A. Convert the ACP communication from out-of-band to in-band channel.

  B. Remove the ACP cabling from the stack before adding the new shelves.

  C. Remove the DS4243 shelves, but you must add the new DS4246 shelves to a new stack.

  D. Configure the shelf IDs of the new DS4246 shelves to match the existing DS4246 shelves.

  Correct Answer: C

• Question 33:

  You are asked to install a 2-node FAS2554 cluster running ONTAP 9.5. The controller arrived with ONTAP

  9.0 installed.

  In this scenario, which two tools would be used to complete this upgrade for this installation? (Choose two.)

  A. HTTP server

  B. SMTP server

  C. FTP server

  D. SNMP server

  Correct Answer: AC

• Question 34:

  You have a 2-node switchless cluster named clusterA. You are planning on adding two additional nodes to clusterA.

  What must you consider before you add the addiHonal nodes to clusterA?

  A. Convert clusterA to a switched cluster by migrating the data lIFs from direct connect to die cluster interconnect switch.

  B. Convert clusterA to a single-node cluster.

  C. Convert clusterA to a switch** cluster by migrating the cluster LIFs from direct connect to the cluster interconnect switch.

  D. Use direct connect to add the additional nodes to clusterA.

  Correct Answer: C

• Question 35:

  Select the Exhibit tab.

  

  Your customer has an AFF A300 installed. They ask you to configure the e0a and e0b ports to use the FC protocol.

  Referring to the exhibit, which statement is correct in this scenario?

  A. These ports are used for the Ethernet uplink into the customer's network.

  B. The configuration of these ports can only be done by OnCommand System Manager.

  C. These ports are used for the cluster interconnect.

  D. Use the ucadmin command to configure these ports as FC ports.

  Correct Answer: C

• Question 36:

  You are asked to install an AFF A700 with two DS224C shelves fully populated. When you arrive, the customer asks you to install an additional shelf.

  Which shelf would you add to this cluster?

  A. a DS224C shelf fully populated with SAS drives

  B. a DS224C shelf fully populated with SATA drives

  C. a DS2246 shelf fully populated with SSD drives

  D. a DS4486 shelf fully populated with SATA drives

  Correct Answer: C

• Question 37:

  Select the Exhibit tab.

  

  The exhibit illustrates the network cabling of a 4-node HA cluster that includes four separate networks. Which two definitions are correct in this scenario? (Choose two.)

  A. Each node must be connected to five distinct networks.

  B. A cluster can be created without data network connections, but it must include a cluster interconnect connection.

  C. Each node may be connected to the management and cluster networks only.

  D. A cluster cannot be created without data network connections, but it must include a cluster interconnect connection.

  Correct Answer: BD

• Question 38:

  A customer wants you to add a new AFF A700 HA pair to an existing 4-node AFF8080 EX cluster. The existing cluster uses netApp CN1610 switches for the cluster connection and is using the recommended port count.

  Which statements is true in the scenario?

  A. You cannot mix different AFF models in the same duster.

  B. There are not enough ports available on the duster switch.

  C. You cannot have more than four nodes with AFF.

  D. The AFF A7O0 is not supported with NelApp CN1610 switches.

  Correct Answer: D

• Question 39:

  A customer wants to reduce the task allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part. The small part is used for the root aggregate and the large part for the data aggregates?

  In this situation, what is this feature called?

  A. ONTAP

  B. RAID

  C. storage virtual machine

  D. Advanced Drive Partitioning

  Correct Answer: D

  Reference: https://community.netapp.com/t5/Data-ONTAP-Discussions/Feature-in-Netapp/td-p/142416

• Question 40:

  You are setting up a new cluster. The customer notices that there are many management ports on the

  cluster. The customer wants to know the purpose of the cluster management LIF.

  In this situation, what should you tell the customer?

  A. The cluster management LIF provides a dedicated IP address for the entire cluster and can fail over to any port in the cluster that is available in the broadcast domain.

  B. The cluster management LIF provides a dedicated IP address for managing a particular node in the cluster and is used for system maintenance.

  C. The cluster management LIF is used to carry intracluster traffic between nodes in a cluster and must be created on a 10GbE network port.

  D. The cluster management LIF provides multiple IP addresses for the entire cluster and can fail over to any cluster or intercluster ports.

  Correct Answer: B