Cisco Cisco Certifications 352-001 Questions & Answers

• Question 81:

  Refer to the exhibit.

  

  Which solution must be used to send traffic from the foreign wireless LAN controller to the anchor wireless LAN controller?

  A. Encapsulate packets into an EoIP tunnel and send them to the anchor controller

  B. Send packets from the foreign controller to the anchor controller via Layer 3 MPLS VPN or VRF-Lite

  C. Send packets from the foreign controller to the anchor controller via IPinIP or IPsec tunnel

  D. Send packets without encapsulation to the anchor controller over the routed network

  Correct Answer: A

• Question 82:

  A customer requests that you determine how much of their remote branch traffic into a central data center is related to a call manager that resides in the data center. Which solution do you recommend?

  A. Enable NetFLow on branch routers

  B. Enable netFlow on central data center routers

  C. Perform SNMP polling of central data center routers

  D. Perform SNMP polling of branch routers

  E. Create an ACL on the local call manager switch with logging enabled

  F. Span traffic from the switch port on the call manager to a data analyzer

  Correct Answer: B

• Question 83:

  Which two statements about AToM are true? (Choose two)

  A. It encapsulates Layer 2 frames at the egress PE

  B. When using AToM, the IP precedence filed is not copied to the MPLS packet

  C. AToM supports connecting different L2 technologies using interworking option

  D. The loopback address of the PE router must be either /24 or /32

  E. It provides support for L2VPN features on ATM interfaces

  Correct Answer: CE

• Question 84:

  Which two techniques are used in an OSPF network design to slow down the distribution of topology information caused by a rapidly flapping link? (Choose two)

  A. LSA throttling

  B. SPF throttling

  C. IP event dampening

  D. Link-state incremental SPF

  E. Link-state partial SPF

  Correct Answer: AC

• Question 85:

  What two options are significant drivers for 5G in IoT networks? (Choose two)

  A. Energy Efficiency

  B. Lower Latency

  C. Mass Connectivity

  D. Programmability

  E. Higher data rates

  Correct Answer: BC

• Question 86:

  Which two options describe the advantages of using DWDM over traditional optical networks? (Choose two)

  A. Inherent topology flexibility with intelligent chromatic dispersion

  B. Inherent topology flexibility and service protection provided without penalty through intelligent oversubscription of bandwidth reservation

  C. Inherent topology flexibility with built-in service protection

  D. Inherent topology flexibility with a service protection provided through a direct integration with an upper layer protocol

  E. Ability to expand bandwidth over existing optical infrastructure

  Correct Answer: AE

• Question 87:

  Which two items are required for data plane hardening of an infrastructure device? (Choose two)

  A. Disable unused services

  B. Routing protocol authentication

  C. SNMPv3

  D. Redundant AAA servers

  E. Infrastructure ACLs

  F. Warning banners

  G. Control Plane Policing

  Correct Answer: AE

• Question 88:

  As a part of a network design, you should tighten security to prevent man-in-the-middle.

  Which two security options ensure that authorized ARP responses take place according to know IP-to-MAC address mapping? (Choose two)

  A. DHCP snooping

  B. ARP spoofing

  C. ARP rate limiting

  D. Dynamic ARP Inspection

  E. Port security

  Correct Answer: AD

• Question 89:

  How must queue sizes be designed to ensure that an application functions correctly?

  A. The default queue sizes are good for any deployment

  B. Each individual device queuing delay in chain must be less than or equal to the application required delay

  C. The queuing delay on every device in chain must be exactly the same

  D. The sum of the queuing delay of all devices in chain must be less than or equal to the application required delay

  Correct Answer: D

• Question 90:

  Which main IoT migration aspect should be reviewed for a manufacturing plant?

  A. Sensors

  B. Security

  C. Applications

  D. Wi-Fi Infrastructure

  E. Ethernet Switches

  Correct Answer: A