Cisco 352-001 Online Practice Questions and Exam Preparation

Cisco 352-001 Online Questions & Answers

• Question 91:

  You are designing a large Frame Relay WAN for a customer. The routing protocol is OSPF. What is the effect on the routing table if the WAN interfaces are configured as point-to- multipoint?

  A. Only a route for the DR will be present in the routing table.
  B. Configuring point-to-multipoint has no effect on the routing table. The route that is configured with the area command will be seen in the routing table.
  C. Multipoint interfaces dynamically add the network of the connected interface.
  D. Multipoint interfaces dynamically add a /32 route for each neighbor in the WAN.
  D. Multipoint interfaces dynamically add a /32 route for each neighbor in the WAN.

• Question 92:

  A company supports IPv4 and IPv6 addresses, and they need to be able to support flow- based translations for ultiple IPv6 devices to a single IPv4 address. Which address family translation design solution should be recommended?

  A. stateful NAT-PT
  B. NAT-PT
  C. stateless NAT64
  D. stateful NAT64
  D. stateful NAT64

• Question 93:

  In a network design, there are three distribution layers and one data center. What are the two main reasons for using a core layer in this design? (Choose two.)

  A. The use of a core layer provides Layer 3 capabilities to the campus.
  B. The core layer reduces the number of ports that are needed in the distribution layers.
  C. The core layer is needed when there are two or more distribution layers that are to be connected.
  D. The core layer would fulfill core network functions such as DPI and security policies.
  E. The core layer is capable of faster forwarding than any other layer or module in the network.
  B. The core layer reduces the number of ports that are needed in the distribution layers.
  C. The core layer is needed when there are two or more distribution layers that are to be connected.

• Question 94:

  You are solving a design failure on a massive Hadoop cluster network that has an application with TCP incast behavior (also known as TCP Throughput collapse) affecting its many-to-one communications with packet loss at the last-hop

  network device.

  Which metric must be measured to ensure that the network provides the best performance for this application?

  A. Availability
  B. Bandwidth utilization
  C. Jitter values
  D. Buffer utilization
  D. Buffer utilization

• Question 95:

  You are redesigning a single-level IS-IS network with 500 routers, which have short-haul and long-haul links Most of the time the routing domain is stable, but periodically interfaces on long-haul links bounce for a short period of time , causing

  10 to 20 flaps in a few minutes. The probable cause is local road construction. Although fast convergence important, the client has concerns about taxing CPU cycles on the older routing platforms.

  What change should you recommend that both protects the CPU of the older routers during the short periods of excessive flapping, yet does not have an impact on fast convergence for all interface failures?

  A. Modify hello timers on routers with short-haul links
  B. Implement LSP generation throttling on routers with long-haul links
  C. Modify the length of time than an LSP remains in the router database without being refreshed on all routers
  D. Implement a delay between successive IS-IS LSP packet transmissions on routers with long-haul links
  D. Implement a delay between successive IS-IS LSP packet transmissions on routers with long-haul links

• Question 96:

  Four routers running IS-IS are connected to a single Ethernet link. Then, a fifth router is connected, which has a priority higher than any of the other routers connected to the network. What will happen?

  A. The new router will become the DIS and cause a temporary disruption in traffic through the link.
  B. The new router will become the DIS without causing a temporary disruption in traffic through the link.
  C. The new router will not be elected DIS unless the current DIS fails.
  D. The new router will not be elected DIS unless it has the lowest NET ID.
  B. The new router will become the DIS without causing a temporary disruption in traffic through the link.

• Question 97:

  What are three drawbacks of VPLS? (Choose three.)

  A. Direct-attached VPLS requires a full mesh of pseudowires.
  B. VPLS cannot support IP bridging (as defined in the VPLS standard).
  C. MAC scalability may be problematic, since customer MACs will be visible on the service provider network.
  D. VPLS requires a large amount of multicast and broadcast replication.
  A. Direct-attached VPLS requires a full mesh of pseudowires.
  C. MAC scalability may be problematic, since customer MACs will be visible on the service provider network.
  D. VPLS requires a large amount of multicast and broadcast replication.

• Question 98:

  Which two statements about VXLAN are true? (Choose two)

  A. VXLAN is a Cisco proprietary solution
  B. VXLAN is an encapsulation method used to create a Layer 3 overlay network
  C. VXLAN can be used to enforce Layer 2 isolation in a multitenant infrastructure
  D. VXLAN uses the Spanning Tree protocol for loop prevention
  E. VXLAN overcomes the 802.1Q virtual LAN address space limitation
  B. VXLAN is an encapsulation method used to create a Layer 3 overlay network
  E. VXLAN overcomes the 802.1Q virtual LAN address space limitation

• Question 99:

  You have been asked to design a wireless network solution that will implement context- aware services on an existing network that was initially deployed for data traffic only. Which two design principles would you follow to increase the location accuracy with the least possible impact on the current setup? (Choose two.)

  A. Use directional antennas to provide better cell separation.
  B. Add access points along the perimeter of the coverage area.
  C. Install additional APs in monitor mode where the cochannel interference would otherwise be affected.
  D. Increase the AP density to create an average interaccess point distance of less than 40 ft.
  E. Fine tune the access points radio configuration to have a higher average transmission power to achieve better coverage.
  B. Add access points along the perimeter of the coverage area.
  C. Install additional APs in monitor mode where the cochannel interference would otherwise be affected.

• Question 100:

  Which is a requirement for performing attack detection by use of anomaly detection technologies?

  A. Baseline data
  B. Packet captures
  C. Syslog data
  D. Exploit signatures
  A. Baseline data