Cisco 350-601 Online Practice Questions and Exam Preparation

Cisco 350-601 Online Questions & Answers

• Question 671:

  A customer data center experiences bandwidth contention that affects the servers connected to the NPV enabled switch.

  The NPV switch is connected to the NPIV switch using two 10 Gb uplinks but the traffic originating front the connected hosts to the core switch exceeds the available bandwidth.

  The engineers decided to add a third uplink to the NPV server to increase the available bandwidth.

  Which set of commands must be used to provision the new uplink?

  A. switch2(config)# npv auto-load-balance ! uplink to NPV Core switch2(config-if)# switchport mode npiv
  B. switch2(config)# npv traffic-map server-interface ! uplink to NPV Core switch2(config-if)# switchport mode npiv
  C. switch2(config)# npv auto-load-balance disruptive ! uplink to NPV Core switch2(config-if)# switchport mode np
  D. switch2(config)# port-channel load-balance ethernet source-dest-port ! uplink to NPV Core switch2(config-if)# switchport mode np
  C. switch2(config)# npv auto-load-balance disruptive ! uplink to NPV Core switch2(config-if)# switchport mode np

  ---

  Explanation

  FC NPV supports disruptive load balancing of server logins. When disruptive load balancing is enabled, FC NPV redistributes the server interfaces across all available NP uplinks when a new NP uplink becomes operational. To move a server interface from one NP uplink to another NP uplink, FC NPV forces reinitialization of the server interface so that the server performs a new login to the core switch.

  Only server interfaces that are moved to a different uplink are reinitialized. A system message is generated for each server interface that is moved.

  Note

  Redistributing a server interface causes traffic disruption to the attached end devices. Adding a member to the existing port-channel does not trigger disruptive auto load-balance.

  To avoid disruption of server traffic, you should enable this feature only after adding a new NP uplink, and then disable it again after the server interfaces have been redistributed.

  If disruptive load balancing is not enabled, you can manually reinitialize some or all of the server interfaces to distribute server traffic to new NP uplink interfaces.

• Question 672:

  Refer to the exhibit. An engineer is configuring Cisco Data Center Network Manager to automate the provisioning of Cisco Nexus 9000 Series Switches. The engineer must configure user access for network engineers to permit device operations in Interface Manager. The solution must hide Admin and Config Menu items in Interface Manager.

  Which two roles must be assigned to the network engineers to meet these requirements? (Choose two.)

  

  

  A. network-admin
  B. global-admin
  C. access-admin
  D. network-operator
  E. san-admin
  C. access-admin
  D. network-operator

• Question 673:

  An online retailer uses 200 cloud-hosted virtual machines (VMs). Currently, the configuration of each VM is performed manually. To support the growth strategy of the retailer, the retailer starts to automatically scale the VMs to meet demand and uses Ansible for configuration management.

  Which action must be performed in Ansible to meet the requirements before automation is performed?

  A. Register each VM in Ansible.
  B. Add each VM to the .ini inventory file.
  C. Set up and configure Ansible Tower.
  D. Configure a dynamic inventory plug-in.
  D. Configure a dynamic inventory plug-in.

• Question 674:

  What is the impact of upgrading the firmware version of the Cisco MDS 9200i Series Switch?

  A. The data plane traffic is not disrupted during the upgrade.
  B. The traffic traversing FCIP tunnel ISL is impacted.
  C. The supervisor performs a switchover to the standby supervisor.
  D. The control plane will have slow multicast convergence.
  D. The control plane will have slow multicast convergence.

• Question 675:

  Refer to the exhibit.

  

  An engineer associates an ESX service profile to a blade server.

  The engineer adds a VLAN to the vNIC Template named vNIC-0 by using Cisco UCS Manager.

  The engineer discovers that the VLAN is missing on the vNIC of the ESX service profile.

  Which action adds the VLAN to the vNIC?

  A. Change Template Type for ESX to Updating Template.
  B. Change Template Type for vNIC-0 to Updating Template.
  C. Remove both templates and recreate them as Updating Templates.
  D. Remove the VLAN from the template and add the VLAN again.
  B. Change Template Type for vNIC-0 to Updating Template.

  ---

  Explanation

• Question 676:

  An engineer must implement a Cisco UCS system at a customer site. One of the requirements is to implement SAN boot. The storage system maps the source WWPN to a unique LUN.

  Which method does Cisco recommend to configure the SAN boot?

  A. Create a SAN boot policy in which every initiator is mapped to the same target LUN.
  B. Define the vHBAs as bootable and leave the default values on the target definition.
  C. Define the vHBAs as bootable and leave the boot target definition empty.
  D. Create a SAN boot policy in which every initiator is mapped to a different target LUN.
  A. Create a SAN boot policy in which every initiator is mapped to the same target LUN.

• Question 677:

  An engineer must configure device aliases for a Cisco MDS 9000 Series Switches-based SAN fabric. The configuration must meet these requirements:

  1. The engineer must be prompted before the changes are committed to the database.

  2. Pending changes must be explicitly displayed on the console.

  Which command accomplishes this task?

  A. device-alias enhanced
  B. device-alias commit
  C. device-alias confirm-commit
  D. device-alias distribute diffs-only
  C. device-alias confirm-commit

• Question 678:

  Refer to the exhibit.

  

  An engineer configures an FCoE connection between a Cisco UCS and a Cisco Nexus 9000 Series Switch. The UCS FI-A connects to the Nexus switch using interface e1/12. All relevant configurations have been completed on the Nexus switch to support FCoE deployment.

  Which action must be taken on Cisco UCS Manager to complete the configuration?

  A. Trunk VLAN 500 on interface e1/12.
  B. Create a Virtual Fibre Channel Interface.
  C. Change the Transport Type to FCoE.
  D. Configure an FCoE uplink interface.
  D. Configure an FCoE uplink interface.

• Question 679:

  DRAG DROP

  Drag and drop the storage technologies from the left onto the correct descriptions on the right.

  Select and Place:

  

  

  ---

  Application

  The release of NFSv4 brought a revolution to authentication and security to NFS exports.

  NFSv4 mandates the implementation of the RPCSEC_GSS kernel module, the Kerberos version 5 GSS-API mechanism, SPKM-3, and LIPKEY. With NFSv4, the mandatory security mechanisms are oriented towards authenticating individual users, and not client machines as used in NFSv2 and NFSv3.

  https://web.mit.edu/rhel-doc/5/RHEL-5-manual/Deployment_Guide-en-US/s1-nfs-security.html

• Question 680:

  Which LDAP rule must be used in Cisco UCS Manager to search for a user continuously down the tree hierarchy until the user is found?

  A. disable secure socket layer
  B. enable group authorization
  C. set group recursion to recursive
  D. Check box of use primary group
  C. set group recursion to recursive