Cisco 350-601 Online Practice Questions and Exam Preparation

Cisco 350-601 Online Questions & Answers

• Question 1:

  DRAG DROP

  Refer to the exhibit.

  

  An engineer must capture fiber channel traffic from the server and Switch Fabric. The traffic must be forwarded to the analyzer.

  Drag and drop the code snippets from the right onto the blanks in the code on the left to complete the configuration. Not all code snippets are used.

  Select and Place:

  

  

• Question 2:

  DRAG DROP

  Refer to the exhibit.

  

  Server 1-must establish an FCoE connection with SW1.

  Drag and drop the code snippets from the right onto the boxes in the code to complete the FCoE configuration of SW1. Not all code snippets are used.

  Select and Place:

  

  

• Question 3:

  DRAG DROP

  Refer to the exhibit.

  

  Drag and drop the code snippets from the bottom onto the blanks in the code to complete the JSON request that implements the ACL presented. Not all code snippets are used.

  Select and Place:

  

  

• Question 4:

  DRAG DROP

  Drag and drop FCoE port types from the right onto the corresponding positions on the left to complete the FCoE deployment. Port types can be used more than once. Not all port types are used.

  Select and Place:

  

  

• Question 5:

  DRAG DROP

  Refer to the exhibit.

  

  An administrator is deploying BGP to geographically connect two data center sites. Both sites are configured for dual-stack routed protocols. The administrator must inject the IPv6 network 2001:AE4:1::/64 into the IPv6 unicast database. Drag and drop the SiteA commands from the right into the blanks in the configuration on the left. Commands are used more than once.

  Select and Place:

  

  

• Question 6:

  DRAG DROP

  An engineer must authenticate OSPF on interfaces of the Cisco Nexus 9000 Series Switch so that:

  1. eth1/1 uses clear text password.

  2. eth1/2 uses encrypted md5 password.

  Drag and drop the commands from the bottom onto the boxes in the code to complete the configuration. Not all commands are used.

  Select and Place:

  

  

• Question 7:

  DRAG DROP

  All logins to a Cisco Nexus 9000 Series Switch must pass through the TACACS+ server at IP address 192.168.10.10. The configuration must meet these requirements:

  1. The TACACS+ server must be used for SSH and Telnet.

  2. The TACACS+ server key must be Cisco123!.

  3. Management VRF must be used for connectivity.

  4. The deployment must fail back to local credentials if the TACACS+ server fails to respond within 30 seconds.

  Drag and drop the code snippets from the right onto the blanks in the code on the left to complete the configuration. Not all code snippets are used.

  Select and Place:

  

  

• Question 8:

  DRAG DROP

  Refer to the exhibit.

  

  An engineer implements a dynamically negotiated LACP port channel on SW1. The port channel members must be configured as active/standby ports with Eth1/2 as active and Eth1/1 as standby. The Eth1/1 interface is configured with default priority. Drag and drop the code snippets from the right onto the blanks in the code on the left to complete the Eth1/2 interface configuration for SW1. Not all code snippets are used.

  Select and Place:

  

  

• Question 9:

  DRAG DROP

  Refer to the exhibit.

  

  During a recent outage, a network engineer discovered that host A started to experience intermittent connectivity, when Leaf102 was down. Drag and drop the code snippets from the bottom onto the boxes in the code to resolve the problem. Not all code snippets are used.

  Select and Place:

  

  

• Question 10:

  DRAG DROP

  Drag and drop the command snippets from the bottom onto the boxes in the code to complete a Python script that displays a list of interfaces on a Cisco Nexus 9000 Series Switch using on-box Python. Not all command snippets are used.

  Select and Place: