Cisco 350-601 Online Practice Questions and Exam Preparation

Cisco 350-601 Online Questions & Answers

• Question 341:

  What is a characteristic of the NFS protocol?

  A. It is used for booting Cisco UCS B-Series servers.
  B. It is used to access a storage array at a block level.
  C. It uses UDP and HTTP as its transport.
  D. It uses remote procedure calls with TCP/IP for transport.
  D. It uses remote procedure calls with TCP/IP for transport.

• Question 342:

  DRAG DROP

  

  The server is sending traffic to the storage server using Fiber Channel protocol. The requirement is for the N5K-1 to forward traffic to MDS9k-1.

  Drag and drop the configuration steps from the right to complete the configuration for N5K-1 on the left. Not all configuration steps are used.

  Select and Place:

  

  

• Question 343:

  An engineer must implement a solution that prevents untrusted DHCP servers from compromising the network. The feature must be configured on a Cisco Nexus 7000 Series Switch and applied to VLAN 10. The legitimate DHCP servers are connected to interface Ethernet 2/4. Which configuration set must be used to meet these requirements?

  A. n7k-1(config)# ip dhcp snooping vlan 10 n7k-1(config)# interface Ethernet2/4 n7k-1(config-if)# ip dhcp snooping verify vlan 10
  B. n7k-1(config)# ip dhcp snooping verify n7k-1(config)# interface Ethernet2/4 n7k-1(config-if)# ip dhcp snooping verify vlan 10
  C. n7k-1(config)# ip dhcp snooping vlan 10 n7k-1(config)# interface Ethernet2/4 n7k-1(config-if)# ip dhcp snooping trust
  D. n7k-1(config)# ip dhcp snooping verify n7k-1(config)# vlan configuration 10 n7k-1(config-vlan)# ip dhcp snooping trust
  C. n7k-1(config)# ip dhcp snooping vlan 10 n7k-1(config)# interface Ethernet2/4 n7k-1(config-if)# ip dhcp snooping trust

• Question 344:

  An engineer must generate a checkpoint of the running configuration on a Cisco Nexus Switch. The checkpoint file name must be called "before_maintenance' and should be used for recovering the switch to its pre-maintenance state. The rollback of the checkpoint to running configuration should only occur if no errors occur. Which two configuration commands must be used to meet these requirements? (Choose two.)

  A. rollback checkpoint file before_maintenance stop-at-first-failure
  B. checkpoint file before_maintenance
  C. checkpoint before_maintenance
  D. rollback running-config file before_maintenance atomic
  E. rollback running-config checkpoint before_maintenance
  B. checkpoint file before_maintenance
  D. rollback running-config file before_maintenance atomic

  ---

  Explanation

  https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/command/reference/security/n5k-sec-cr/n5k-sec_cmds_r.html

  rollback checkpoint is invalid command. Rollback should be to running configuration, not a checkpoint rollback can be selected by a name or file name. the difference between them is using the "file" keyword.

• Question 345:

  An engineer must design an automation solution for the Cisco ACI Fabric to speed up the deployment of logical network elements for tenant provisioning. When creating a solution, the engineer must keep in mind that the tool must support these requirements:

  1. Allow the rapid creation and removal of logical containers.

  2. Support the creation of custom modules and data structures.

  3. Be extensible with external libraries and modules.

  4. Allow rapid testing of code using an on-demand execution environment.

  Which automation tool meets these requirements?

  A. SaltStack
  B. YAML
  C. Chef
  D. Python
  C. Chef

• Question 346:

  A network engineer needs to upgrade the EPLDs of the fabric modules for a Cisco MDS director-class switch.

  In which order are components reloaded during the process?

  A. one fabric module at the time
  B. all fabric modules followed by the entire switching platform
  C. all fabric modules in parallel
  D. one module and one supervisor at the time
  D. one module and one supervisor at the time

• Question 347:

  What is the effect of enabling Skip Validation in the Cisco UCS Auto Install process?

  A. The firmware image of Cisco UCS is not installed.
  B. The upgrade process of Cisco UCS fails to complete.
  C. Cisco UCS Manager does not report issues with the upgrade.
  D. Users that are logged in to Cisco UCS Manager are logged out.
  C. Cisco UCS Manager does not report issues with the upgrade.

• Question 348:

  Refer to the exhibit

  

  A Cisco MDS 9000 Series Switch is configured with RBAC

  The default role applies to all users User A is also assigned to the rote Custom-Role-B Which set of features will user A be authorized to configure?

  A. hardware environment TACACS+
  B. NTP SSH DPVM
  C. DPVM NTP SSH hardware
  D. SSH DPVM TACACS+ NTP
  D. SSH DPVM TACACS+ NTP

• Question 349:

  An engineer must configure multiple EPGs on a single access port in a large Cisco ACI fabric without using VMM integration. The relevant access policies and tenant policies have been created. A single AAEP is used to configure the access port in the fabric.

  Which two additional steps must be taken to complete the configuration? (Choose two.)

  A. A contract must be defined between the EPGs
  B. The EPGs must be linked to the correct physical domain
  C. The EPGs must link directly to the corresponding AAEP
  D. The corresponding bridge domains must be configured in legacy mode
  E. The EPGs must be configured as static ports
  B. The EPGs must be linked to the correct physical domain
  E. The EPGs must be configured as static ports

• Question 350:

  Refer to the exhibit.

  

  The network 10.1.1.15/32 is advertised to N9K1. N9K2 and N9K3 OSPF neighbors in area 1.

  Which configuration advertises network 10.1.1.15/32 as LSA type 7 to N9K3?

  A. N9K2(config-router)# area 1 stub no-summary N9K3(config-router)# area 1 stub
  B. N9K1(config-router)# area 0 nssa N9K2(config-router)# area 0 nssa
  C. N9K1(config-router)# area 0 stub no-summary N9K2(config-router)# area 0 stub
  D. N9K2(config-router)# area 1 nssa N9K3(config-router)# area 1 nssa
  D. N9K2(config-router)# area 1 nssa N9K3(config-router)# area 1 nssa

  ---