Cisco 350-080 Online Practice Questions and Exam Preparation

Cisco 350-080 Online Questions & Answers

• Question 61:

  When configuring vPC-HM CDP with multiple links to the same switch, are port-channels required?

  

  A. Each link between the upstream switch and the VEM is an individual subgroup.
  B. Connections that go to the same upstream switch must be configured with the command channel-group mode active.
  C. Connections that go to the same upstream switch must be configured with the command channel-group mode passive.
  D. With vPC-HM CDP, the user can pin traffic from a specific VM to a specific uplink.
  E. Connections that go to the same upstream switch must be configured with the command channel-group mode on.
  E. Connections that go to the same upstream switch must be configured with the command channel-group mode on.

• Question 62:

  Which two statements about SAN port channels configured on Cisco Nexus 5000 Series switches are true? (Choose two.)

  A. The bring up protocol automatically detects and overrides any misconfiguration.
  B. You can manually configure channel groups, or they can be automatically created.
  C. Changes in configuration to the SAN port channel interface must also be made to all members of the channel group.
  D. The port channel protocol uses the exchange fabric parameters command to communicate across peer ports in an ISL.
  E. The port channel protocol ensures that a set of ports is eligible to be part of the same SAN port channel.
  B. You can manually configure channel groups, or they can be automatically created.
  E. The port channel protocol ensures that a set of ports is eligible to be part of the same SAN port channel.

• Question 63:

  In a Cisco Unified Computing System, What is the "designated receiver" port in end-host mode used for?

  A. Sending all broadcasts
  B. Receiving all traffic from upstream switches
  C. Receiving broadcast traffic
  D. Negotiating spanning tree with upstream switches
  E. Learning MAC addres?ses from upstream switch?es
  C. Receiving broadcast traffic

• Question 64:

  Drag Drop

  Select and Place:

  

  

• Question 65:

  Refer to the exhibit.

  

  When the engineer tried to check CoPP on the switch, the engineer observed the error that is shown in the exhibit. Which option describes the reason for the displayed output?

  A. The Cisco NX-OS version that is running does not support CoPP.
  B. The CoPP feature is not enabled on this switch.
  C. The CoPP CLI is available from the default VDC.
  D. CoPP is enabled by default but not configured.
  C. The CoPP CLI is available from the default VDC.

• Question 66:

  Which three statements about IPv4 ACLs and the IPsec feature are true? (Choose three.)

  A. Cisco SAN-OS software allows only name-based IPv4 ACLs.
  B. The IPsec feature considers source and destination IPv4 and IPv6 addresses.
  C. IKE traffic (UDP port 500) is encrypted.
  D. The IPsec feature does not support port number ranges.
  E. Inbound and outbound traffic is evaluated against the same outbound IPv4 ACL.
  A. Cisco SAN-OS software allows only name-based IPv4 ACLs.
  D. The IPsec feature does not support port number ranges.
  E. Inbound and outbound traffic is evaluated against the same outbound IPv4 ACL.

• Question 67:

  Refer to the exhibit.

  

  You configured a port on a Cisco Nexus 7000 switch as a trunk port. Which VLANs are allowed on the trunk port based on the port configuration in the exhibit?

  A. No VLANs are allowed by default. Use the switchport trunk allowed vlan 1-4094 command to allow all VLANs.
  B. Only Native VLAN 1 will be allowed.
  C. VLANs 1 to 3967, and 4048 to 4094 are allowed.
  D. VLANs 1 to 3900, and 4048 to 4094 are allowed.
  E. VLANs 1 to 4094 are allowed.
  C. VLANs 1 to 3967, and 4048 to 4094 are allowed.

• Question 68:

  Which three components does a data center network layer have? (Choose three.)

  A. Cisco GSR
  B. Cisco CRS - 1
  C. Cisco Nexus 7000
  D. Cisco Nexus 1000V
  E. Cisco Nexus 2000
  F. Cisco ASR 9000
  G. Cisco Nexus 5000
  C. Cisco Nexus 7000
  E. Cisco Nexus 2000
  G. Cisco Nexus 5000

• Question 69:

  Where is a typical request in the Cisco UCS XML API placed in the data management engine, and, after the request is confirmed, what is updated?

  A. The request is placed in the transactor queue in FIFO order and the management information tree is updated.
  B. The request is placed in the replicator and persistifier and the store is updated.
  C. The request is placed in the data management engine and the application gateway is updated.
  D. The request is placed in the buffer queue and the commit buffer queue is updated.
  A. The request is placed in the transactor queue in FIFO order and the management information tree is updated.

• Question 70:

  What tasks can only be performed in the default or admin VDC?

  A. EPLD upgrade, IOS ISSU, FcoE feature enablement, CoPP configuration, and rolling back a checkpoint
  B. EPLD upgrade, Cisco IOS ISSU, FCoE feature enablement, CoPP configuration, and ACL capture enablement
  C. EPLD upgrade, Cisco IOS ISSU, FCoE feature enablement, CoPP configuration and SNMP configuration
  D. EPLD upgrade, Cisco IOS ISSU, FCoE feature enablement, CoPP configuration, and write erase
  B. EPLD upgrade, Cisco IOS ISSU, FCoE feature enablement, CoPP configuration, and ACL capture enablement