Cisco 350-080 Online Practice Questions and Exam Preparation

Cisco 350-080 Online Questions & Answers

• Question 51:

  Refer to the exhibit.

  

  Based on the output, what is the most likely reason for the failure of the iSCSI boot?

  A. There is no gateway configured on the iSCSI vNIC.
  B. The LUN is not masked correctly on the storage array.
  C. CHAP authentication is not configured correctly.
  D. The latency between the imitator and target is too high.
  B. The LUN is not masked correctly on the storage array.

• Question 52:

  Which two options are advantages of deploying Ethernet-based FCoE switches such as the Cisco Nexus 7000 Series Switches beyond the access layer? (Choose two)

  A. lower overall throughput compared to native Fibre Channel switches
  B. flexibility to support file (NAS) and block (iSCSI and FCoE) storage traffic
  C. High-performance Ethernet-based FCoE switches cannot be used in a dedicated SAN core.
  D. requirement for traffic isolation with dedicated links and storage VDCs is no longer required.
  E. plans that include 40 and 100 Gigabit Ethernet speeds
  B. flexibility to support file (NAS) and block (iSCSI and FCoE) storage traffic
  E. plans that include 40 and 100 Gigabit Ethernet speeds

• Question 53:

  Refer to the exhibit.

  

  Which two statements about the output and diagram are true? (Choose two.)

  A. FI-A is configured in FC switch mode.
  B. VSAN trunking is enabled on FI-A.
  C. The native VSAN should be VSAN 1.
  D. Cisco UCS will allow all VSANs by default when FC trunking is enabled.
  E. FI-A requires VSAN pruning.
  F. Interface fc1/8 on MDS-A should be configured as a TE Port.
  B. VSAN trunking is enabled on FI-A.
  D. Cisco UCS will allow all VSANs by default when FC trunking is enabled.

• Question 54:

  On a Cisco Unified Computing System (UCS), which two statements regarding Ethanalyzer are true? (Choose two.)

  A. Interface inbound-low handles Rx and Tx of low-priority control packet
  B. Interface inbound-lo handles Rx and Tx of high-priority control packet
  C. Interface inbound-low maps to internal interface eth3
  D. Interface inbound-low maps to internal interface eth4
  A. Interface inbound-low handles Rx and Tx of low-priority control packet
  C. Interface inbound-low maps to internal interface eth3

• Question 55:

  In the event of a GSS failure in a GSS cluster, which is true?

  A. The current connections are rerouted via the backup GSS
  B. Secondary GSS cannot be used to configure the GSS cluster
  C. All remaining GSSs in the cluster continue responding to any new queries
  D. All records in the GSS database are flushed and reconstructed again using a new master GSS
  C. All remaining GSSs in the cluster continue responding to any new queries

• Question 56:

  On a Cisco Nexus 7000 Series Switch, what is the purpose of this command?

  Switch# config terminal

  switch(config)# mac address-table learning-mode conversational vlan 1-10

  switch(config)#

  A. Enable conversational learning on FabricPath vlans 1-10 for F-Series module
  B. Enable FabricPath protocol on VLANs 1?0
  C. No need for this command as conversational learning is enabled by default for all VLANs.
  D. Enable conversational learning on Classical Ethernet VLAN for F-Series module
  A. Enable conversational learning on FabricPath vlans 1-10 for F-Series module

• Question 57:

  The hardware and software configurations for vPC+ are similar to that of traditional vPC. What are the differences in the configuration of vPC+? (Choose three.)

  A. FabricPath switch ID must be configured under the vPC domain.
  B. Virtual switch ID of vPC+ must be configured under FabricPath domain.
  C. On Cisco Nexus 7000 Series Switch, F1 interfaces must be used as the vPC+ peer links.
  D. The vPC+ peer link must be configured as a Cisco FabricPath core port (switchport mode fabricpath).
  E. FabricPath subswitch ID must be configured under the vPC domain.
  A. FabricPath switch ID must be configured under the vPC domain.
  C. On Cisco Nexus 7000 Series Switch, F1 interfaces must be used as the vPC+ peer links.
  D. The vPC+ peer link must be configured as a Cisco FabricPath core port (switchport mode fabricpath).

• Question 58:

  Which Sticky method is supported by Cisco ACE?

  A. SIP
  B. SSL session ID
  C. scripted
  D. HTTP return code parsing
  B. SSL session ID

• Question 59:

  Refer to the exhibit.

  

  An administrator is setting up the VSM and VEM in Layer 3 mode. The administrator adds a host to the distributed switch in VMware, but does not see the module join the VSM. Given the configuration in the exhibit, which three configuration items must be included in the configuration? (Choose three.)

  A. The vEthernet Port Profile parameter must be set to Capability I3control.
  B. The vEthernet Port Profile parameter must be set to VSM l3control.
  C. The Ethernet Port Profile parameter must be set to System VLAN 1400.
  D. The Ethernet Port Profile parameter must be set to VLAN 1400 in the allowed trunk.
  E. The Ethernet Port Profile parameter must be set to Capability l3control.
  F. The vEthernet Port Profile parameter must be set to Mode Trunk.
  G. The vEthernet Port Profile parameter must be set to VEM l3control.
  A. The vEthernet Port Profile parameter must be set to Capability I3control.
  C. The Ethernet Port Profile parameter must be set to System VLAN 1400.
  D. The Ethernet Port Profile parameter must be set to VLAN 1400 in the allowed trunk.

• Question 60:

  Which option is an advantage of Cisco ACE virtual IP address tracking?

  A. Troubleshooting is possible between multiple routing domains and multiple service devices.
  B. Tracking is limited to a maximum of 500 tracked instances.
  C. New virtual IP address implementation has multiple network touchpoints.
  D. It can be used during application migration in which virtual IP addresses cannot be changed.
  D. It can be used during application migration in which virtual IP addresses cannot be changed.