Cisco 350-080 Online Practice Questions and Exam Preparation

Cisco 350-080 Online Questions & Answers

• Question 141:

  Refer to the exhibit.

  

  Which two options describe information that can be determined from this output? (Choose two.)

  A. the uplink interface that is operating as the designated receiver for broadcast traffic
  B. the uplink interface that is operating as the designated sender for broadcast traffic
  C. the switching mode for which the Fabric Interconnect is configured
  D. the uplink interface from which multicast traffic will be sourced
  E. whether the last respond code was accepted or not
  A. the uplink interface that is operating as the designated receiver for broadcast traffic
  C. the switching mode for which the Fabric Interconnect is configured

• Question 142:

  Refer to the exhibit.

  

  vPC+ is configured between which switches?

  A. Switch-ID 13 and Switch-ID 23
  B. Switch-ID 11 and Switch-ID 12 C. Switch-ID 100 only
  D. Switch-ID 13 and Switch-ID 100
  A. Switch-ID 13 and Switch-ID 23

• Question 143:

  In the event of a catastrophic disaster, after which you need to replace the entire UCS blade system (that is, new fabric interconnects, new IOMs, new chassis, and new blades), what type of backup would provide the most complete set of information?

  A. logical configuration
  B. all configuration
  C. full state
  D. system configuration
  C. full state

• Question 144:

  What does the command "IP ARP synchronize" do in a vPC configuration?

  A. Synchronizes ARP entries between vPC peers every five minutes
  B. Triggers a manual update of ARP entries from the primary peer to the secondary
  C. Enables a bulk loading of ARP entries when a vPC peer is restored
  D. Uses the peer-keepalive link to maintain ARP table consistency
  C. Enables a bulk loading of ARP entries when a vPC peer is restored

• Question 145:

  Refer to the exhibit.

  

  Given the displays from N5K-1 and N5K-2, what is the expected result if the zone mode enhanced vsan 1 command is issued on N5K-1?

  A. The mode change will complete with a warning that the zone database from N5K-1 will be distributed throughout the fabric.
  B. The mode change will not complete due to the mismatch in the default zone mode.
  C. The mode change prompts the administrator to override the default zone mismatch and make them the same.
  D. The mode change completes, and the default zone setting remains unchanged in N5K-1 and N5K-2.
  E. The default zone setting is set to deny in both switches because it is more secure.
  A. The mode change will complete with a warning that the zone database from N5K-1 will be distributed throughout the fabric.

• Question 146:

  Basic zoning changes are accomplished through the use of four SW_ILS frames. Which option identifies these frames in the correct order?

  A. RCA, UFC, SFC, ACA
  B. ACA, RCA, SFC, UFC
  C. SFC, UFC, ACA, RCA
  D. ACA, SFC, UFC, RCA
  E. UFC, SFC, RCA, ACA
  D. ACA, SFC, UFC, RCA

• Question 147:

  Refer to the exhibit.

  

  Which option describes the capability that the FCoE setting allows?

  A. configures the FEX to send FCoE traffic only to this switch
  B. allows mapped VLAN-VSAN traffic to reach the FEX
  C. configures FEX for A-B SAN capabilities
  D. allows interface Ethernet 101/1/1 to exchange DCBX information
  A. configures the FEX to send FCoE traffic only to this switch

• Question 148:

  Refer to the exhibit.

  

  Which statement about these commands is true?

  A. The outputs of the debug are redirected on file test on the "log." directory.
  B. The outputs of the debug are redirected to the logging buffer.
  C. The command does not have an effect unless you configure "debug enable".
  D. If you are on a console connection, the outputs are shown after the event occurs.
  A. The outputs of the debug are redirected on file test on the "log." directory.

• Question 149:

  Drag and drop the call home severity on the left to the correct description on the right.

  Select and Place:

  

  

• Question 150:

  What does the previously active supervisor do when "system switchover" is issued?

  A. State is transferred and then becomes ha -standby.
  B. A core dump file is written, state is transferred, and the system resets.
  C. State is transferred; the supervisor reloads and becomes ha -standby.
  D. State is transferred; data plane operations are briefly suspended and then become ha - standby.
  C. State is transferred; the supervisor reloads and becomes ha -standby.